Haynes Forums

Haynes Forums (http://www.haynes.co.uk/forums/index.php)
-   Announcements (http://www.haynes.co.uk/forums/forumdisplay.php?f=2)
-   -   hi and progress so far (http://www.haynes.co.uk/forums/showthread.php?t=13369)

garyt 27th June 2014 09:38 PM

hi and progress so far
 
1 Attachment(s)
So after building a locost and then losing it when I got divorced here we go with round 2 !! with encouragement from my new missus who is dead keen on the whole idea I decided to go down the mx5 route.
incidentally not that my missus is a petrolhead but she had a mustang when we met stateside where I managed to get my first speeding fine , red mustang doing 90 on the interstate and £180 for the pleasure, enjoy the usa sir !!
anyway now we are back in sunny lossiemouth, Scotland and have got my chassis onto 4 wheels and am waiting for the engine to arrive from way down south
here is a pic of progress so far

http://www.haynes.co.uk/forums/attac...d=140389774 7

Davidbolam 28th June 2014 12:21 AM

Welcome to the forum. Nice to see yet another mx5 builder. If you have any questions please ask.

I'm guessing your in the raf with your location

David

garyt 28th June 2014 12:36 AM

hi David many thanks , no im not RAF I am a cooper and I make whisky barrels for a living :) for my sins. Had many bikes over the years, an mgb, tvr 3000m, xr4x4 then had to be sensible and didn't like it so here we are doing what we enjoy .
thanks again for the welcome gary

Enoch 28th June 2014 09:37 AM

Looking good, what engine are you going for? The Mazda one or something a bit more exotic / ridiculous?

garyt 28th June 2014 09:12 PM

yes just the plain old mazda this time, not even close to finishing, and already the missus has said what SHE wants in hers :)
So let her pick the colour and I'll teach her how to drive it on the proper side of the road and then..... :D

K4KEV 29th June 2014 02:10 AM

Welcome Gary the cooper....was'nt he a film star:p looking forward to watching another haynes take shape.

jason 82 29th June 2014 08:22 AM

Welcome to the forum Gary, Rally Design do some really good deals, just bought a set of Gaz coilovers for £380 including springs & shipping. Very impressed ! Phil of Talon Motorsport on this forum does loads of fabricating work, the mx5 engine mount brackets are a must, makes the job a lot easier, then we have K4kev , he is the fuel tank guru. There are some really clever people on here, handy to know. Don't ask me anything, I am learning as I go ! Lol:eek: :D

alga 29th June 2014 11:35 PM

Word or warning: your headlight stalks seem to be on the long side. Mine are shorter and I'm thinking of shortening them still, because the lights impact the cycle wings on full lock and suspension compression. The nose cone does not project outside the top chassis rails, so you you can judge the gap there by offering a cardboard cutout of your chosen headlight size or just measuring the distance between the headlight mounting hole and the top chassis rails. As for the 400 mm maximum dimension between the side of the car and the edge of the headlight, just remember that the widest point of the car is at the rear arches and it is 169-170 cm depending on your tub and wings. You can work out the minimum distance between the light mounting holes based on that width and the size of your lights.

Update: that said, I positioned the bulge of the cycle wings right beside the headlight, so you might be fine:

garyt 30th June 2014 08:06 PM

hi many thanks for that I will do some measuring and adjust as needed, I'd rather cut them now if I need to !:D

garyt 23rd July 2014 09:24 PM

1 Attachment(s)
hi been busy at work but took home the heavy mob today and trina fed them in exchange for putting my engine and box in ! seriously picked it up and said where do you want it?
end of box was still full of oil though so while I swept up they had coffee. at least now I can get engine mounts made up and crack on again.
Gary :D

http://www.haynes.co.uk/forums/attac...d=140614312 6


All times are GMT +1. The time now is 10:44 PM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.