Haynes Forums

Haynes Forums (http://www.haynes.co.uk/forums/index.php)
-   Bodywork and interior (http://www.haynes.co.uk/forums/forumdisplay.php?f=8)
-   -   Fibre glassing question..Fabby ?? (http://www.haynes.co.uk/forums/showthread.php?t=2867)

dogwood 8th October 2009 01:46 PM

Fibre glassing question..Fabby ??
 
Hi.
Im about to modify my Triton scuttle. (Widen it)
I have made up the "Splash" molding as Mark sudgested.
Question is,
Do I need to use Gelcoat before the matting or will just the resin be OK?
I intend to spray it anyway so finish is not an issue.
I have some very old gelcoat in my garage.(25 years:eek: )
Does it go off?
Sorry if these are dumb questions, but what I know about fibreglassing could be put on a postage stamp, and still have room for the queens head....:rolleyes:

David
I

fabbyglass 8th October 2009 07:10 PM

Yes mate it goes off, resin and gel coat have a shelf life of a year i think it is if stored in right conditions.
You might be ok just using matt and resin as no doubt it will need a skim of filler to get the levels right as not dead flat on the top...;)

dogwood 8th October 2009 07:27 PM

Cheers mate

So you think after 25 years it might be past it's best then..:D
I'll give it a go over the weekend, see how I get on..:rolleyes:

Fingers crossed for me, hu ?:D

David

fabbyglass 8th October 2009 08:07 PM

Cut the matt to fit into gap, nice sharp edge for first layer then 2 over the top overlaping by 4 " or so either side...dont get it too wet and not too dry;)

dogwood 8th October 2009 08:22 PM

Quote:

Originally Posted by fabbyglass (Post 22927)
.dont get it too wet and not too dry;)

So sort of in be tweeny......

Cheers for the advice, greatly appreciated.
Coz I know nuffffin about fibreglassin.

David

fabbyglass 8th October 2009 08:43 PM

Yeah something like that but you will know when you do it, have a look on the underside(if i did it right that is...:o ) how it looks and aim for that finish..although it's cured it kinda looks wet/shiney well ish..Too much resin and it will get hot and be brittle not enough and it will fall apart.

RAYLEE29 9th October 2009 10:38 AM

just by coincidence ive been doing exactly that to a westfield scuttle that i picked up before i knew it wouldnt fit and a nose cone that dont fit either
both bought before i started my chassis and before i came here and learnt my mistake
if it works itll be good if not its only time and a little bit of resin etc
Ray:)

dogwood 9th October 2009 02:03 PM

Splash mould.....
 
It's not even FUNNY!!!:eek:

Do you think I did something wrong with my splash mould...?:rolleyes:
Said I don't know nuffin bout fibreglassin...





David

RAYLEE29 9th October 2009 04:03 PM

OOPS! did you wax the panel before you applied that?
or is it delaminated through not being enough resin or did the resin go off before you applied it?
Ray:confused:

fabbyglass 9th October 2009 05:42 PM

I would say you never waxed it. It sticks like shit to a blanket when you don't want it to but when you do it will fall off unless you prepare the surface...good fun aint it:o

If taking a splash mould then wax 3 or 4 times and pva if not sure on the surface.

If repairing then badger the surface with gritty paper to key it then wipe with acetone to remove the wax present in resin/gel coat.


All times are GMT +1. The time now is 08:34 PM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.