Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > SVA/Legal
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 9th July 2012, 08:51 PM
Spikehaus Spikehaus is offline
Senior Member
 
Join Date: Aug 2008
Location: Plymouth, Devon
Posts: 484
Default IVA Checklist

IVA Queries

Rear Registration Plate

2) The space must permit the mounting of a plate in a position as close to vertical as possible taking into account the shape of the bodywork.

Does anyone know if the angle of the rear tub is acceptable to pass the IVA, or will a wedge be required to make the number plate nearer to vertical?

Also, does anyone have any key points I should be checking?

Plastic Nut / Bolt Covers - Tick
GRP Cycle Wing Trim - Tick
Cycle Wing Stay Brackets - Tick
Bonnet Edge Trim - Tick
Aeroscreen Trim - Tick (Does the lower return require trim as well)
Rear Tub Trim - Tick
Inner Edges of Scuttle Return - Tick
Inner Edge of Nosecone - Tick
Steering rack / Top Wishbone Ball Joint Nuts - Tick
Steering Rack Extension Rubber Gland Cover - Tick
Flexi Brake Hose onto front caliper - Tick
Trim to underside of Headlight Mounts - Tick
Fog Light Vertical - Tick
Exhaust Silencer - Tick

Correct E Marking on Lights UPDATE (Ozzy1)
Seatbelt Boss Gusset UPDATE (Deezee)
Thread sticking out of nylocs UPDATE (Deezee)
Roll bar main bolts need to have strength rating on them UPDATE (Deezee)

Any help appreciated to make sure its all covered.

Last edited by Spikehaus : 11th July 2012 at 08:49 AM.
Reply With Quote
  #2  
Old 9th July 2012, 09:15 PM
SeriesLandy's Avatar
SeriesLandy SeriesLandy is offline
Senior Member
 
Join Date: Nov 2008
Location: Portsmouth
Posts: 828
Default

Per iva pics would be a good idea. Much easier to spot anything glaringly obvious.
__________________
Steve
My Photo Album | Haynes Roadster FAQ | IVA Forms How To
Reply With Quote
  #3  
Old 9th July 2012, 09:54 PM
Spikehaus Spikehaus is offline
Senior Member
 
Join Date: Aug 2008
Location: Plymouth, Devon
Posts: 484
Default

Loads of photos of the flicker Hyperlink N06

Also, the IVA manual states that fuel filler caps cannot be in a luggage compartment, so is the rear tub a considered as a luggage compartment? Will I require an external filler pipe?

Last edited by Spikehaus : 9th July 2012 at 09:56 PM.
Reply With Quote
  #4  
Old 9th July 2012, 10:26 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,393
Default

Are we close to another car on the road then

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #5  
Old 9th July 2012, 11:43 PM
PorkChop PorkChop is offline
Senior Member
 
Join Date: Jul 2011
Posts: 394
Default

I haven't heard of anyone needing a plinth for the rear number plate. The MEV Exocet has an angled rear plate area too and I haven't heard of anyone needing a plinth for that either.

I would imagine that if you don't have a boot floor, then you wouldn't have a luggage compartment.
Reply With Quote
  #6  
Old 10th July 2012, 02:31 AM
ozzy1's Avatar
ozzy1 ozzy1 is offline
Senior Member
 
Join Date: Jul 2009
Location: perth,australia
Posts: 760
Default

If u dont have a lid on it or a bottom it can't be a luggage compartment.Also u wouldn't have a rear number plate fitted for IVA as u need the Iva to get a number plate?
Reply With Quote
  #7  
Old 10th July 2012, 02:35 AM
ozzy1's Avatar
ozzy1 ozzy1 is offline
Senior Member
 
Join Date: Jul 2009
Location: perth,australia
Posts: 760
Default

Only one I can think of is do all of your lights have the correct 'e' markings on them.There was a link I think in the announcements section I think with this info.
Reply With Quote
  #8  
Old 10th July 2012, 02:00 PM
deezee's Avatar
deezee deezee is offline
Senior Member
 
Join Date: Jan 2009
Location: Wirral
Posts: 744
Default

Its hard to tell as I'm not sure how up to date the Flickr photos are. For me I picked up on.

- Rear roll bar braces only have 1 bolt - (ashg IVA Failure)
- Roll bar main bolts need to have strength rating on them, or supporting paperwork.
- Thread sticking out of nylocs. They'll even ask you to take off your rubber nut covers to ensure the nylocs have enough thread going through them.
- Edge projection applies to all edges, so you'll fail if you don't cover the rear seatbelt gussets on the roll bar.
- You've covered your fuel pipe coming from the tank, will they be able to read the writing on it, for its suitability for use with petrol?
Reply With Quote
  #9  
Old 10th July 2012, 11:04 PM
baz-r baz-r is offline
Senior Member
 
Join Date: Nov 2009
Posts: 1,464
Default

Quote:
Originally Posted by Spikehaus View Post
Loads of photos of the flicker Hyperlink N06

Also, the IVA manual states that fuel filler caps cannot be in a luggage compartment, so is the rear tub a considered as a luggage compartment? Will I require an external filler pipe?
if its in a inclosed area the iva man will not like the look of it so leave the cover off
if its open at the bottom area of your tub you might get away with it.
i think its all about fuel vapor in enclosed spaces
Reply With Quote
  #10  
Old 11th July 2012, 01:10 PM
deezee's Avatar
deezee deezee is offline
Senior Member
 
Join Date: Jan 2009
Location: Wirral
Posts: 744
Default

Just going through the notes and checks I made for my IVA and thought of the following.

- 19mm radius on the bottom of the dashboard
- Secondary fixing for the upright mushrooms
- Correct radius where aluminium panels meet the chassis local to seats (on the curved section)
- Can your, or your passengers knees / legs touch anything under the scuttle? I had to box it in on the passenger side.

Last edited by deezee : 11th July 2012 at 01:13 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 12:34 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.