Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Running gear
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 21st June 2019, 03:49 PM
Numplumb Numplumb is offline
Senior Member
 
Join Date: Aug 2012
Posts: 191
Default

My rear upper wishbones are a lot shorter than the lower ones.
MX5 rear upper wishbones are a lot shorter than the lower ones.
As far as I know unequal length wishbones are the preferred arrangement.
IMO making longer adjusters or moving the anchor points won't alter the geometry enough to be a problem, there isn't very much movement in the rear suspension anyway, and if you set it at 1% negative at the ride height it probably will only go to 0% when cornering.

Regards Mick.
Reply With Quote
  #12  
Old 22nd June 2019, 07:40 AM
bentovey bentovey is offline
Member
 
Join Date: Aug 2018
Posts: 56
Default

Hi Mick, is your chassis the Saturn one using the original diff case?
Mine is the talon chassis using my version of Phil’s diff case (as he’s no longer making them)
My wishbones are also talon ones but I’ve not really seen many other people using them (front upper ones are curved not triangular and front lowers have an upward bend in them)
On the rears the upper adjusters have to be wound out almost all the way to get -1 degree of negative camber (45mm of thread showing)
So my plan is to re-make the adjusters with an extra 40mm of thread just for piece of mind, unless of course you can see any reason why that would be a bad idea
__________________
Statistically only one in seven dwarves are happy
Reply With Quote
  #13  
Old 22nd June 2019, 10:02 AM
Numplumb Numplumb is offline
Senior Member
 
Join Date: Aug 2012
Posts: 191
Default

Yes my chassis is to Saturn spec.
My front lower wishbones also have a bend in them, Talon made them that way because there was a problem with track rod ends touching the inside of the rim.
My upper front ones are triangular and only have adjustments on the upper ball joints.
My rear lower wishbones have adjusters, but the upper ones don't.
If your upper rears are very short compared to the lower ones like mine are there is only about 50mm of up and down movement, so I can't see it making much difference if you make longer adjusters because the wishbones are going to be where they are now but without only a small bit of thread left in the wishbones.
Regards Mick.
Reply With Quote
  #14  
Old 22nd June 2019, 10:06 AM
Numplumb Numplumb is offline
Senior Member
 
Join Date: Aug 2012
Posts: 191
Default

Hi I never put any photos of my build three on here but if you look at Stot's build thread you will see lots of pictures of his wishbones etc.
His where made by Talon and are the same as mine.
Regards Mick.
Reply With Quote
  #15  
Old 22nd June 2019, 10:26 AM
bentovey bentovey is offline
Member
 
Join Date: Aug 2018
Posts: 56
Default

Thanks Mick, I read Stots build last week (great build) my upper rear wishbones are about 40-50mm shorter than my lowers so if I extend the adjusters by 40mm it should in theory make them of equal length.
I’ll try them out without shocks in and cycle through the travel to see how it affects camber.
Cheers
Ben
__________________
Statistically only one in seven dwarves are happy
Reply With Quote
  #16  
Old 22nd June 2019, 10:59 AM
Numplumb Numplumb is offline
Senior Member
 
Join Date: Aug 2012
Posts: 191
Default

Hi yours must be completely different from mine.
I can't see how your upper wishbones will move from where they are now, by making the adjusters longer it seems to me that if you have them set at the moment with 1% neg but not enough thread left in the wishbones by making them longer will leave them as they are but with more thread in the wishbones.
Equal length wishbones is not a good setup shorter uppers is the best.
Regards Mick.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 12:03 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.