#331
|
||||
|
||||
I have to say I wouldn't want to risk using a cracked flywheel, as when it goes it goes, and with already being cracked it is just a matter of time before the cracks grow long enough until fast fracture can occur.
Not really something you want to risk : http://www.youtube.com/watch?v=0NYZV...eature=related
__________________
1.8 Silvertop Zetec (ZX6R Carbs + Megajolt) + Type 9 My Build Blog: http://www.haynes.co.uk/forums/showthread.php?t=2736 - Last Update: 31st October 2020 Total Spent so far: Stopped counting |
#332
|
|||
|
|||
Reduction valve
When you installed the brake pressure reduction valve in your rear brake line what size of union was used on the input side? It seems a lot bigger than 10 x 1.
I was trying to work out which way around it went until I came across the question you had asked on the ma5da racing forum. David
__________________
Click to see my build photos on Flikr http://www.flickr.com/photos/67112582@N03/ Saturn MX5 Based Chassis, Limited Slip Diff & 2.4 Quick Rack. Build cost.... seems to be spending more on tools than car bits at the moment! (they will be handy in the future though). Car iva'd and passed 15/08/2014. Finished weight 572kg. |
#333
|
||||
|
||||
Quote:
My local friendly garage had a dig through their pot of brake unions and found one the right size |
#334
|
||||
|
||||
I think it must be time for an update!
Haven't had a huge amount of time to spend on the build for the last couple of months, but slowly managed to strip the engine down and replace the head. Also swapped the scary cracked flywheel with a decent second hand one I picked up via mx5nutz. The free engine stand I got from the tip came in handy! Actually got a decent session in the garage for the first time in ages tonight, and managed to get the engine into the chassis: The bonnet fits, which is nice! |
#335
|
||||
|
||||
Good effort, just need to get it running now
TT
__________________
You only get a woosh with a dump valve Build Thread Man Cave Mantiques Cecil Street Auto Repairs Garage Carlisle Build Cost £4181.65 - Last - Wheel Cylinders |
#336
|
||||
|
||||
Thanks TT. Hopefully won't be too long before I get it running, just need to sort out the spaghetti under my scuttle
|
#337
|
||||
|
||||
Wow, your spaghetti looks super tidy compared to mine. I'm trying to use the Sierra fusebox, and it looks like a tangle of wires.
__________________
Albert Haynes Roadster FAQ | Haynes Builder Locations Gallery, build thread in Lithuanian / via Google Translate. |
#338
|
|||
|
|||
Looking really good skov. I was looking at your photos. In the second album what is the blue cylinder shaped item. It looks like it is the last photo on there.
david
__________________
Click to see my build photos on Flikr http://www.flickr.com/photos/67112582@N03/ Saturn MX5 Based Chassis, Limited Slip Diff & 2.4 Quick Rack. Build cost.... seems to be spending more on tools than car bits at the moment! (they will be handy in the future though). Car iva'd and passed 15/08/2014. Finished weight 572kg. |
#339
|
||||
|
||||
Quote:
If you mean this, it's my fuel pump. I'm currently figuring out where to stick it! I think I'm going to do something similar to Alga here: http://www.haynes.co.uk/forums/showthread.php?t=8197 |
#340
|
|||
|
|||
Are you not using the in tank mx5 one?
__________________
Click to see my build photos on Flikr http://www.flickr.com/photos/67112582@N03/ Saturn MX5 Based Chassis, Limited Slip Diff & 2.4 Quick Rack. Build cost.... seems to be spending more on tools than car bits at the moment! (they will be handy in the future though). Car iva'd and passed 15/08/2014. Finished weight 572kg. |
Thread Tools | |
Display Modes | |
|
|