Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Running gear
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 28th February 2010, 03:14 AM
correl correl is offline
Senior Member
 
Join Date: Jan 2010
Posts: 105
Default The Front suspension

I was thinking today about how the standard front arms seem dangerous..


Looking at the way the suspension is set up the lower arm takes all the wieght of the car while the upper are just becomes a track contol arm. Now on the original donor car the weight of the car comes down on the top of the knuckle, the lower part of the knuckle is not designed to take wieght. Anyone that has built these cars how you put a brace of any sort between the upper and lower arms? It would take the weight off the lower joint and distribute to the upper arm also.
Reply With Quote
  #2  
Old 28th February 2010, 10:17 AM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

I think if you did all the drawings of where force is applied, you would find a large proportion of the force goes lateraly through the top wishbone.

The front suspension nuckle will not stay upright without the upper wishbone so the force and weight must be being taken somewhere.

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #3  
Old 28th February 2010, 10:23 AM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

It's also a standard basic design that has been used for decades in all sorts of cars form humdrum family compacts to formula one cars.

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #4  
Old 28th February 2010, 10:23 AM
Bonzo's Avatar
Bonzo Bonzo is offline
Senior Member
 
Join Date: Jul 2007
Location: Cornwall
Posts: 3,321
Thumbs down Dangerous

Dangerous ..... That's a bit of a strong word to use there

I am no design engineer but even I can see that the lower wishbone does not carry the entire weight of the front of the car !!??
Most of the weight will be tranfered to the main chassis structure Via the front shock's

The addition of braces or drop links as they are better known will only serve to assist anti roll .... Being that the Roadster does not suffer badly with body roll, not a lot of point fittng them !!??

Do you not think that VOSSA might have picked up any dangerous design defects !!!

There are thousands of 7 type cars out there .... All using the same type of wishbone design & that includes the original Lotus 7

One last point !! This type of wishbone design was used for many years on F1 cars & even with the advent of the Carbon fibre age .... Current F1 wishbones are still not a world apart ( theory wise ) to our humble wishbones .

Rant over
__________________
I am not a complete idiot...........Some of the parts are missing !!
Ronnie

www.roadster-builders.co.uk
Reply With Quote
  #5  
Old 28th February 2010, 10:43 AM
deezee's Avatar
deezee deezee is offline
Senior Member
 
Join Date: Jan 2009
Location: Wirral
Posts: 744
Default

What is the problem with the lower wishbone taking the load and having it absorbed by the shock absorber? Its exactly the way its meant to be. As pointed out, this is a tried and tested design. Bearing in mind the car isn't the same weight as a Sierra, so its hardly dealing with the same loads.

Hold on.... your post is at 2am! I'm sure your here to wind up this forum.
Reply With Quote
  #6  
Old 28th February 2010, 10:54 AM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

you would probably find that if you left off the inner lower wishbone bolts, that the car would still remain off the ground with the wheels upright

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #7  
Old 28th February 2010, 11:17 AM
correl correl is offline
Senior Member
 
Join Date: Jan 2010
Posts: 105
Default

Yoiu are all not seeing what i mean. The lower arm is attached by a ballljoint yes. In Formula 1 the knuckle is designed to take the weight there. In the case of all the cars used to build this car the shock and spring is normally standard in the top of this knuckle. The just look and the size difference in the metal between the top and the bottom of the knuckle. On the kit cars the rolls the parts have to play are reversed.

Think about it the lower ball joint has the whole weight of the car and have to contend with the spring and shock stopping it from giving on bumps while the upper arm moves freely and just follows the knuckle.


Are these lower joints as a question common for replacing on mots by any chance? Bet the upper on ain't so prone to it.


Last edited by correl : 28th February 2010 at 11:31 AM. Reason: Adding image
Reply With Quote
  #8  
Old 28th February 2010, 11:33 AM
correl correl is offline
Senior Member
 
Join Date: Jan 2010
Posts: 105
Default

Quote:
Originally Posted by deezee View Post
Hold on.... your post is at 2am! I'm sure your here to wind up this forum.
No just thinking about what i am building and so couldn't sleep
Reply With Quote
  #9  
Old 28th February 2010, 11:36 AM
deezee's Avatar
deezee deezee is offline
Senior Member
 
Join Date: Jan 2009
Location: Wirral
Posts: 744
Default

A more general question about the design of Lotus 7 inspired kitcars, might be better put forward to the Locost Builders.

No one has had a problem with the design yet. I'm sure borrowing parts from cars are putting them in a different chassis isn't what the manufacturer intended, but it works.
Reply With Quote
  #10  
Old 28th February 2010, 11:36 AM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

The upper arm does not just follow though, Because the wheel center is further out than the hub center line the wheel tilts inwards under load, this transferes across the wishbone into the chassis.

See my crude attatched drawing.

Production cars used double wishbones for decades before mcpherson stuts became common.

TT
Attached Images
File Type: jpg spen.JPG (10.3 KB, 69 views)
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 05:32 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.