Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Bodywork and interior
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 24th January 2017, 05:25 PM
jps jps is offline
Senior Member
 
Join Date: May 2012
Location: Colchester, Essex
Posts: 439
Default GRP sides a bit tight (in places!)

I've been dry fitting my GRP sides and found that they vary between being just right, too loose and too tight.

This is probably partly because I have gone for a 3mm alu floor and there are some areas where I can dress a couple of welds and maybe get 1mm back to work with...

Just right I can deal with.
Too loose is not so bad either - thanks to seeing how Sylvain has dealt with similiar challenges here: http://forums.haynes.co.uk/showthread.php?t=13363

The 'too tight' bit has already led to me putting a small crack in the gelcoat - presumably from trying to flex it too far - so I am not going to force the panels in place.

Any tips for what options I have to make things fit? Can I sand out the inside (i.e. the non-gelcoat side) of the panel to introduce a bit more room?
Reply With Quote
  #2  
Old 24th January 2017, 05:50 PM
vmax1974's Avatar
vmax1974 vmax1974 is offline
Senior Member
 
Join Date: Apr 2011
Location: Teesside
Posts: 1,141
Default

You will be able to samd some of the glass resin side where it is too tight everyone has this problem and i am looking into ways of adding a mm leaway but i havent had any ideas yet that havent meant i have to remake the moulds
Reply With Quote
  #3  
Old 25th January 2017, 12:19 PM
Cropper Cropper is offline
Member
 
Join Date: Jul 2013
Posts: 92
Default

I removed the bottom return (but left the radius) & fastened the side panels with heavy duty velcro, then just ran a small bead of silicon along the inside. I used a 5mm dome head bolt at the front & rear for extra security, the rear one isn't seen & the front one isn't noticeable as its low down by the bottom wishbone, also used black bolts on black side panels.
The velcro works well & it's takes a lot to reomove the side panels, i also used it to fasten down the top of my transmission tunnel, which makes for easy access if reqd.
Reply With Quote
  #4  
Old 26th January 2017, 12:14 AM
vmax1974's Avatar
vmax1974 vmax1974 is offline
Senior Member
 
Join Date: Apr 2011
Location: Teesside
Posts: 1,141
Default

I will add the sides to my list of new moulds
Reply With Quote
  #5  
Old 26th January 2017, 07:20 AM
Ben_Copeland's Avatar
Ben_Copeland Ben_Copeland is offline
Senior Member
 
Join Date: Feb 2009
Posts: 290
Default

As above. Reduce down the thickness of the lip if possible.

I managed to get mine on without having to take any off. They were tight in places but gentle pressure slowly working along got them to stretch enough.
Reply With Quote
  #6  
Old 27th January 2017, 02:05 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

on mine, (equinox) one side fit ok and the other side was to tight and wouldn't go on, i used a sanding flap wheel in an angle grinder and sanded the inside edges till they went on, i did have to take quite a bit out if i remember correctly
__________________
http://www.haynes.co.uk/forums/showthread.php?t=13517

My Build Thread
Reply With Quote
  #7  
Old 27th January 2017, 10:30 PM
jps jps is offline
Senior Member
 
Join Date: May 2012
Location: Colchester, Essex
Posts: 439
Default

Thanks everyone, my panels are Equinox also so good to know it's not just me!
Reply With Quote
  #8  
Old 1st February 2017, 08:45 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

Original saturn pannels.

3mm Chequer plate floor.

Cut the lower lip off.
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #9  
Old 5th February 2017, 01:46 AM
jps jps is offline
Senior Member
 
Join Date: May 2012
Location: Colchester, Essex
Posts: 439
Default

Quote:
Originally Posted by twinturbo View Post
Original saturn pannels.

3mm Chequer plate floor.

Cut the lower lip off.
How did you attach them to the chassis?
Reply With Quote
  #10  
Old 5th February 2017, 06:21 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

not finished but will use a length of angle to pull them in.

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 06:52 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.