|
#1
|
||||
|
||||
Ford EEC-IV wiring (1993 Mondeo, Zetec 2.0)
I plan on running Zetec 2.0 with the standard engine loom and stock engine management. On various forums the Ford EEC-IV is complimented as being smart enough to be useful and practical, but simple enough not to cause too much trouble.
As it's been a bit too cold to spend time in the workshop, I've been spending time sorting out the looms I have in the warmth of my home. Broke a Mondeo and a Sierra loom for wires and plugs, also tracked down each wire and plug within the Mondeo Zetec harness. Now I have spreadsheet of the ECU pinout with colours and functions, and a tag on each wire coming into the three oval plugs that connect the engine loom to the body loom: https://fridge.pov.lt/~alga/zetec/Mondeo-ECU-pinout.pdf (editable spreadsheet version) My engine management has the coil drivers built into the ECU, systems with EDIS-4 might have slight differences in the ignition wiring. To summarize, you just need to feed battery positive, main power positive, ignition positive, and battery negative in order to run the engine with the stock ECU. The rest of the wires coming out of the engine loom are various senders and non-essential sensors and outputs. There isn't even a check engine light coming out of that ECU! Removing EGR, pulse air and canister purge relays/sensors from the system might upset the ECU (codes will be visible in the self test), but they should not throw it into limp mode. If they cause any problems, they can be stubbed with appropriate resistors. If you decide to go this route, I recommend getting the Haynes manual for the engine donor. The Mondeo's Haynes wiring diagrams are much easier to read than Sierra's, as they have all the numbered components listed on the same page. If you don't want to buy a paper version, for Mondeo, usually googling for 1923-12.PDF will do the trick! Speaking of wiring, the injector/CMP/temp sensor subharness was completely Kaput on my engine. Out of 12 wires in that subharness there wasn't a single one with isolation fully intact. I suspect the engine wiring was the main reason why the Mondeo was broken: The main part of the engine harness is in a pretty good shape. Only the crank angle sensor wires and the EGR valve plug wires are damaged. EGR will be deleted anyway, and the CKP plug I replaced. I found out that the square plugs used for injectors and most sensors on the Zetec are of the Tyco/AMP Junior Power Timer series. Getting replacement crimped contacts for them will not be much problem. But I've still no clue what the oval 12-point plug is called. In the worst case I'll solder the wires to the old contacts.
__________________
Albert Haynes Roadster FAQ | Haynes Builder Locations Gallery, build thread in Lithuanian / via Google Translate. |
#2
|
|||
|
|||
Hi Albert. I'm going the same way. Have you figured out if removing the purge,egr and pulse upsets the running at all? I'm using a DEEP Ecu which has the inbuilt Edis
__________________
Total cost so far Materials £3,150 Tools £855 |
#3
|
|||
|
|||
If you need to replace just the pins in the plug itself rather than solder the wires on to short tails these people are most likely to have them.
http://www.vehicle-wiring-products.e...e/homepage.php And if you need the tool for getting the critters out snap on do this and its not dear to buy, i have had mine years and its had a lot of use. http://directory.pten.com/product/10...et_No_SGTT106A Bob
__________________
When The Results Disagree With The Theory: Believe The Results And Invent A New Theory If I had two brains I,d still be a halfwit The cave http://s1116.photobucket.com/user/my...deshow/mancave The build http://www.haynes.co.uk/forums/showthread.php?t=12669 |
#4
|
||||
|
||||
Oooh, thanks a lot for the pointers. I was going to get the contacts from the generic electronics suppliers like Digikey or Farnell. JPT terminals are widely available, but the 1.6 mm round pin system of the oval plug appears to be quite rare.
As for deleting pluse air, canister purge and EGR sensors & valves, I haven't been able to try it out yet.
__________________
Albert Haynes Roadster FAQ | Haynes Builder Locations Gallery, build thread in Lithuanian / via Google Translate. |
#5
|
||||
|
||||
Quote:
It also runs fine with out the speed sensor But I do plan on refitting that as there are meant to be other gains such as fuel cut on over run ect. Dont limit your self to the early eec-iv as the Pat's is no big deal as long as you have the matching key and you gain the obd2 function. Ive done several and had one I did through iva Pre 95 deep ecu http://youtu.be/Pxq4ks2Us_U Post 95 (1997)104 pin eec-v with Pats owls ecu http://youtu.be/BKqeCjdBM0w 1999 104 pin eec-v with pats Olw5 ecu. This was wired for a midi and shows how few connections there are. Done so the user only had perm live switched live, a few earths, fuel pump and there is one for the tacho. http://youtu.be/pUbV0NPvx4M
__________________
Nowt again. |
#6
|
||||
|
||||
Quote:
Some really usefull information there Big W
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie www.roadster-builders.co.uk |
#7
|
||||
|
||||
Quote:
__________________
Nowt again. |
Thread Tools | |
Display Modes | |
|
|