Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > General discussion
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #21  
Old 31st October 2014, 09:55 PM
garyt garyt is offline
Senior Member
 
Join Date: Jun 2014
Location: Dufftown, scotland
Posts: 480
Default

[quote=Rosco;99095]Your build seems to be moving on well too! Cheers

thanks ,trying to get all the plumbing done for the supercharger and sort out the exhaust manifold / pipework, also started stripping down the wiring harness ( it was a bit parky out so dining room floor was commandeered) getting some more bits together to make another push forward,
seems to be lots of bits and not a lot of room
really looking forward to the electrics... mmmmm
Reply With Quote
  #22  
Old 2nd November 2014, 07:07 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

We had another good weekend, my dad help too so got a bit done

Started off welding up the shock towers, my weldings ok but my mate who's a pro is going to weld my chassis up







Reply With Quote
  #23  
Old 2nd November 2014, 07:08 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default





Then tacked the roll bar on



Then the diff mounts

Reply With Quote
  #24  
Old 2nd November 2014, 07:08 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

Then made some foot plates for the rear stays



Next all the suspension brackets, which took a bit of time to make sure they were as good as they could be, we tweaked the legs of the front frame out to close the gap between the brackets so no packing was needed





Then took it from my workshop into my garage ready to go for welding next week

Reply With Quote
  #25  
Old 2nd November 2014, 07:09 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default







Reply With Quote
  #26  
Old 2nd November 2014, 07:10 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default



That's that, got the workshop tied out so we could move again as it was getting a bit tight with the chassis in there,

Then just cut the tube up ready for the wishbones







Thanks for looking!
Reply With Quote
  #27  
Old 2nd November 2014, 07:44 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

Quote:
Originally Posted by SeriesLandy View Post
You seem to be blazing along. You'll be finished by next summer at this rate.
If you haven't already, make the plate that the steering column goes through from 3mm steel not the book 1mm. It's a real pita to change it after it's been fully welded on.
Ok mate cheers, prob use 2mm then as I'm trying to keep it as light as possible, is 1mm to thin then?
Reply With Quote
  #28  
Old 2nd November 2014, 08:00 PM
SeriesLandy's Avatar
SeriesLandy SeriesLandy is offline
Senior Member
 
Join Date: Nov 2008
Location: Portsmouth
Posts: 828
Default

Quote:
Originally Posted by Rosco View Post
Ok mate cheers, prob use 2mm then as I'm trying to keep it as light as possible, is 1mm to thin then?
It will flex when you brake. I changed mine to 3 and it was hard changing it afterwards. It also isn't really think enough for the steering column bearing.
Plan on using a different one if your going for a sierra column.
guide
Search ebay for SLFL 25 Self Lube Bearing.
Lastly. Cut out plate where the handbrake cable goes through and weld it in vertical rather than on an angle, as it puts pressure of the handbrake cable and doesn't let it flow as easily. Lastly cut 2 slits into the plate so you can get the cable through the plate without taking the cable to bits.
I hope I don't sound too bossy but they are things I would have done the first time if I was doing the car again.
__________________
Steve
My Photo Album | Haynes Roadster FAQ | IVA Forms How To
Reply With Quote
  #29  
Old 2nd November 2014, 08:20 PM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

Quote:
Originally Posted by SeriesLandy View Post
It will flex when you brake. I changed mine to 3 and it was hard changing it afterwards. It also isn't really think enough for the steering column bearing.
Plan on using a different one if your going for a sierra column.
guide
Search ebay for SLFL 25 Self Lube Bearing.
Lastly. Cut out plate where the handbrake cable goes through and weld it in vertical rather than on an angle, as it puts pressure of the handbrake cable and doesn't let it flow as easily. Lastly cut 2 slits into the plate so you can get the cable through the plate without taking the cable to bits.
I hope I don't sound too bossy but they are things I would have done the first time if I was doing the car again.
Ok mate cheers, no problems, grateful for the input, how wide do the slits want to be? And I will order a bearing in a min!

Thanks again
Reply With Quote
  #30  
Old 2nd November 2014, 08:24 PM
SeriesLandy's Avatar
SeriesLandy SeriesLandy is offline
Senior Member
 
Join Date: Nov 2008
Location: Portsmouth
Posts: 828
Default

If your going to use mx5 bits you will need a different bearing btw.
For the sierra shaft you will also need part of the original bearing. (It's all in the guide)

For the cables, about 2-3mm slits just enough to get the cable through.
__________________
Steve
My Photo Album | Haynes Roadster FAQ | IVA Forms How To
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:19 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.