Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > SVA/Legal
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 13th October 2016, 07:53 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default reduce emissions

One of the points i have just failed on the IVA is for having high CO2 readings. I have a mx5 engine and a cat before the back box. Can anyone advise how i can bring my emissions down further? The IVA man mentioned some people, especially with motorbike engines are using a smart controller to control the emission output?
__________________
One day it will be on the road......
Reply With Quote
  #2  
Old 14th October 2016, 06:42 PM
garyt garyt is offline
Senior Member
 
Join Date: Jun 2014
Location: Dufftown, scotland
Posts: 480
Default

Hi is it the std ecu and induction side? As I had my mx5 with sports cat standard ecu and std plenum plus supercharger and it was spot on
Do you have the egr takeoff on your ex manifold going to the egr valve
__________________
remember we are not mad just creatively insane
Reply With Quote
  #3  
Old 14th October 2016, 08:35 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default

I have a JDM loom hence there is no egr, i have blanked it off. shall i maybe look to try wiring it into the loom, if it can be done?
__________________
One day it will be on the road......
Reply With Quote
  #4  
Old 15th October 2016, 12:37 PM
garyt garyt is offline
Senior Member
 
Join Date: Jun 2014
Location: Dufftown, scotland
Posts: 480
Default

What ecu are you using ? The egr valve is there to help the emissions if yo have a programmable ecu then a remap session not for power but just to do the co2 to get you through iva then remap proper after if your going to end up with a Q reg then it would be an easy way to do it
__________________
remember we are not mad just creatively insane
Reply With Quote
  #5  
Old 15th October 2016, 01:23 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default

The ECU and loom is from an import hence it doesnt have an egr valve connector as part of the loom. The engine does have and egr valve though hence i will try and wire it into the circuit if its possible without it being controlled by the ecu.
Failing that i guess i can ask my local garage if they can help remapping it...
__________________
One day it will be on the road......
Reply With Quote
  #6  
Old 16th October 2016, 04:45 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default

Just checked and there is no connector in the loom for the egr valve. Any ideas how i can wire it into the loom but not controlled by the ecu?
__________________
One day it will be on the road......
Reply With Quote
  #7  
Old 16th October 2016, 07:19 PM
PorkChop PorkChop is offline
Senior Member
 
Join Date: Jul 2011
Posts: 394
Default

How will the EGR valve be controlled if it isn't connected to the ECU? That is assuming that the JDM ECU has the controller logic installed/switched on for the EGR valve in the first place...

I think you need to go back to the beginning. The EGR is a red herring.

Are you sure you're talking about CO2?

If you're talking about CO, which I suspect you are, then what limit did it fail, at what lambda etc.? What limit did it have to meet? What were the HCs like?
Reply With Quote
  #8  
Old 16th October 2016, 09:03 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default

I hope there is an easier soution to this, and yes it is CO not CO2. Ooops.
I was reading 0.68 at fast idle and need 0.20 to pass. Lambda pasted fine, HC is 88.
__________________
One day it will be on the road......
Reply With Quote
  #9  
Old 17th October 2016, 11:44 AM
flyerncle flyerncle is offline
Senior Member
 
Join Date: Mar 2008
Location: gateshead,near cobbly bit of A1 North
Posts: 3,188
Default

O2 sensor 1 in manifold controls fuel in relation to rear O2 sensor,ect switch also controls fuel in relation to temp,so possibly ect switch is faulty.
__________________
Cost : Little as possible.
Thanks : To those who by their generosity my build has progressed.
Its a handmade sports car not a flaming kit car !!!


If at first you dont succeed,avoid skydiving...

No parachute require to freefall,only if you want to do it twice.
Reply With Quote
  #10  
Old 17th October 2016, 02:10 PM
Wain Wain is offline
Member
 
Join Date: Feb 2012
Location: Hull
Posts: 68
Default

I think we might be onto something with the ECT sensor, after we did the emissions test the engine was very hot as expected but then cut out after back firing a bit. It starts fine now its cool so can only assume it over heated, water pipes were warm but not as hot as i expected. Maybe the sensor is ok but an issue with the coolant not circulating?
__________________
One day it will be on the road......
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 06:34 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.