Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Bodywork and interior
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 24th February 2014, 05:16 PM
voucht's Avatar
voucht voucht is offline
Senior Member
 
Join Date: Jun 2011
Location: Lautrec, Tarn (81), Occitanie, France
Posts: 879
Default Body/floor/interior rivets and rivnuts

Hi,
I'm going to get my chassis back from the sandblasting/powder coating at the end of the week.

I will soon put the floor, interior panels, and I am also going to receive my body kit from Equinox some day this week.

My floor will be made out of 3mm thick aluminium, inside panels out of 1.2mm thick aluminium. Thickness of my tube walls is 2mm.

I was wondering what kind of rivets do I need to buy : diameter? length? Are aluminium rivets OK? The books says 3mm rivets for the inside panels and body elements, at 50mm spacing. Do you think this is OK? And will this rivets spacing and diameter be OK for fitting my aluminium floor too (3mm rivets sounds a bit small to me)?

also, where did you use Rivnuts to be able to remove the panel?

If you guys would like to share your experiences about that, and give me good advices, I would be glad

Thanks a lot.
Reply With Quote
  #2  
Old 24th February 2014, 05:40 PM
flyerncle flyerncle is offline
Senior Member
 
Join Date: Mar 2008
Location: gateshead,near cobbly bit of A1 North
Posts: 3,188
Default

What ever you decide and 3mm 1/8 are ok,still use Sikaflex/PU to glue it to the chassis.
I did this and used plenty of rivets and the car is raced and no problems,consider placing you seats on a strip of steel across floor and fixed to outer and trans tunnel rails for piece of mind and you wont find your undercarriage dragging along the road.
__________________
Cost : Little as possible.
Thanks : To those who by their generosity my build has progressed.
Its a handmade sports car not a flaming kit car !!!


If at first you dont succeed,avoid skydiving...

No parachute require to freefall,only if you want to do it twice.
Reply With Quote
  #3  
Old 24th February 2014, 08:44 PM
SeriesLandy's Avatar
SeriesLandy SeriesLandy is offline
Senior Member
 
Join Date: Nov 2008
Location: Portsmouth
Posts: 828
Default

I used 3.2mm sealed rivets for the floor and a hell of a lot of them.
I also riveted the transmission tunnel sides and the top above the gearbox.
I used 5mm rivnuts for the transmission tunnel top.
I used 6mm rivnuts for the side panels, scuttle, nosecone rear tub and arches.

My only annoyance with the sealed rivets (the ones I bought) is that they left a 4mm long spike sticking up as the break point wasnt at the top of the rivet.

You don't realise how many times you take the bodywork off.
I tired to leave the riveted panels to last but I still had to take one off again as I had an oil leak on the propshaft seal.

HTH
__________________
Steve
My Photo Album | Haynes Roadster FAQ | IVA Forms How To
Reply With Quote
  #4  
Old 24th February 2014, 11:21 PM
mgglep's Avatar
mgglep mgglep is offline
Senior Member
 
Join Date: Apr 2011
Location: leicestershire
Posts: 212
Default

I used 3 mm Ali floor I used sikaflex 3/16 or 4.8mm rivets at 50mm pitch which where sealed and steel rivets for strength remember if you do you steel rivets on Ali you will need to put a blob of sealer or paint or something as the steel and Ali will react together. I did use countersunk rivets where the side panels fit and I am glad I did as the side panels where tight
__________________
17.07.10 "Now i know the meaning of life"
My Build pics
http://www.flickr.com/photos/67605695@N04/
http://www.flickr.com/photos/97412063@N08/
Reply With Quote
  #5  
Old 25th February 2014, 09:01 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

My floor, Trans sides and seat back are rivited. All other panels are designed to be removeable.

Floor was rivets and FSS ( F.....g Sticky Stuff )

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #6  
Old 25th February 2014, 09:03 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 03:49 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.