Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Chassis
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #21  
Old 29th November 2012, 10:19 PM
The V8 Files The V8 Files is offline
Senior Member
 
Join Date: Jul 2011
Location: Biggleswade, Bedfordshire
Posts: 346
Default

Mostly pushing, found it a lot easier, I think I get what yo mean about focusing on the thicker piece but don't get the sucky bit
Reply With Quote
  #22  
Old 29th November 2012, 11:31 PM
Talonmotorsport's Avatar
Talonmotorsport Talonmotorsport is offline
Senior Member
 
Join Date: Oct 2007
Location: Southminster Essex
Posts: 1,323
Default

Welds are fine as they are curtainly not bird poo examples either wind wire feed back a little or up the rate of weld ie go alittle faster, this is MIG welding and the welds will be proud of the surface no matter what.
__________________
Website http://www.talonmotorfabrication.co.uk/

Direct email phil@talonmotorfabrication.co.uk

talonmotorfabrication@gmail.com

Mobile office hours 07514098334
Reply With Quote
  #23  
Old 29th November 2012, 11:44 PM
robo robo is offline
Senior Member
 
Join Date: Jun 2011
Location: scabs
Posts: 1,722
Default

I am going out a limb here bruce and reckon you might have a crap helmet/ sight glass. Your welds in the corners are good but the stuff on the flats is all over the place. I think your good in the corners because you have two flats at 90 degrees to guide you. Try a lighter glass and weld between two scribe lines as a guide and see how you get on.

Bob
__________________
When The Results Disagree With The Theory: Believe The Results And Invent A New Theory
If I had two brains I,d still be a halfwit

The cave http://s1116.photobucket.com/user/my...deshow/mancave

The build http://www.haynes.co.uk/forums/showthread.php?t=12669
Reply With Quote
  #24  
Old 30th November 2012, 12:02 AM
The V8 Files The V8 Files is offline
Senior Member
 
Join Date: Jul 2011
Location: Biggleswade, Bedfordshire
Posts: 346
Default

Bob, this is the helmet I'm using, I'm pretty sure I've got travel rate and consistency issues but I'm not sure the helmets helping as I'm still struggling with seeing the joint, will give it a try with scribing and chalking as dualist mentioned when I get set up for a next play

Cant do much more now as I've run out of tube, have to go scrounging round the industrial estates

In the meantime I'l get my eyes tested, I should get that up to date regardless.

http://www.weldairsupplies.co.uk/swp...9-13-152-p.asp


Last edited by The V8 Files : 30th November 2012 at 12:09 AM.
Reply With Quote
  #25  
Old 30th November 2012, 12:11 AM
robo robo is offline
Senior Member
 
Join Date: Jun 2011
Location: scabs
Posts: 1,722
Default

Those speedy glass things are not brilliant if you have light coming in from behind. I dont get on with them.

Bob
__________________
When The Results Disagree With The Theory: Believe The Results And Invent A New Theory
If I had two brains I,d still be a halfwit

The cave http://s1116.photobucket.com/user/my...deshow/mancave

The build http://www.haynes.co.uk/forums/showthread.php?t=12669
Reply With Quote
  #26  
Old 30th November 2012, 12:16 AM
The V8 Files The V8 Files is offline
Senior Member
 
Join Date: Jul 2011
Location: Biggleswade, Bedfordshire
Posts: 346
Default

You think Its worth a try without the main lights on? The main ceiling lights running down the centre?
Reply With Quote
  #27  
Old 30th November 2012, 12:25 AM
Talonmotorsport's Avatar
Talonmotorsport Talonmotorsport is offline
Senior Member
 
Join Date: Oct 2007
Location: Southminster Essex
Posts: 1,323
Default

I have a £2.99 Ikea (other lamps are available) desk lap above my bench which balances out the 8 strip lights behind me, just be sure that you don't have the filter set too senseative or it goes dark before you've even started.
__________________
Website http://www.talonmotorfabrication.co.uk/

Direct email phil@talonmotorfabrication.co.uk

talonmotorfabrication@gmail.com

Mobile office hours 07514098334
Reply With Quote
  #28  
Old 30th November 2012, 08:40 PM
alga's Avatar
alga alga is offline
Senior Member
 
Join Date: Feb 2009
Location: Vilnius, Lithuania
Posts: 1,249
Default

DoS, do a destructive test or two. Weld a piece of box to the longer tube with just one fillet seam and then flex it until it breaks off.
__________________
Albert
Haynes Roadster FAQ | Haynes Builder Locations
Gallery, build thread in Lithuanian / via Google Translate.
Reply With Quote
  #29  
Old 1st December 2012, 12:55 PM
The V8 Files The V8 Files is offline
Senior Member
 
Join Date: Jul 2011
Location: Biggleswade, Bedfordshire
Posts: 346
Default

Thanks Albert, yes I think I need to do some testing like you suggest, also if I can find a small enough amount I'l get some etching solution and do some slicing and checking.

I have a couple of little hobby lights which I've tried and also without the lighting behind me, neither made much difference so hopefully chalking and scribing will help.
Reply With Quote
  #30  
Old 2nd December 2012, 11:28 AM
robo robo is offline
Senior Member
 
Join Date: Jun 2011
Location: scabs
Posts: 1,722
Default

I am not knocking the testing but really once you have the hang of it you know in an instant if the weld is any good or not. You should be in a position by the time you start welding the chassis to know if there is penetration or not and that just comes with heaps of practice. You need clear vision of whats going on and plenty of time with the torch in your hand. Judging your first attempts at mig you wont be long Its also a big mistake to just roll stuff around on the bench, as soon as you are happy with that start on some positional stuff. The learning curve begins again with vertical, horizontal and overhead., all of which you will need at some point in the build.

Bob
__________________
When The Results Disagree With The Theory: Believe The Results And Invent A New Theory
If I had two brains I,d still be a halfwit

The cave http://s1116.photobucket.com/user/my...deshow/mancave

The build http://www.haynes.co.uk/forums/showthread.php?t=12669
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 02:06 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.