Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Running gear
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 10th January 2010, 10:50 AM
dogwood's Avatar
dogwood dogwood is offline
Senior Member
 
Join Date: Mar 2008
Posts: 899
Default

Yup.
Seemed to be perfek.
Hard to beleive for £3.85,
especialy as some people want 20 quid for the mod
__________________
.
.
David.

Heaven, Warm days and Cool rides
Reply With Quote
  #12  
Old 10th January 2010, 10:55 AM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

so when reamed, the OD of the lower hole should be at 16mm.

Cool.

Cheers

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #13  
Old 10th January 2010, 11:03 AM
dogwood's Avatar
dogwood dogwood is offline
Senior Member
 
Join Date: Mar 2008
Posts: 899
Default

See, now you getting complicated.

When I did mine I kept doing a bit then tested it, till I got about half the thread through.
So when I tightened it up it pulled in snug without the thread bottoming out.

Not sure, but think if you did it till the bottom was 16mm it may be too much.
You will need someone that has done one recently to be sure.
__________________
.
.
David.

Heaven, Warm days and Cool rides
Reply With Quote
  #14  
Old 10th January 2010, 12:09 PM
HandyAndy's Avatar
HandyAndy HandyAndy is offline
Senior Member
 
Join Date: Jan 2009
Location: cleveland
Posts: 3,917
Default

i did mine as Dogwood suggests,

a little at a time, keep checking that you haven,t gone too far,

takes about 10 mins per upright, do it like tapping a thread, half turn in quarter turn back.... keeps the cutting edge of the reamer clean of swarf & helps get a clean cut on the steel.

cheers
andy
__________________
Flat Pack Chassis Kits for sale, contact me at andyroadster@yahoo.co.uk
Reply With Quote
  #15  
Old 10th January 2010, 12:16 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

Sounds easy enough, I just remember when I started a Locost back in 2004 that this was one of the difficult bits to get done ( or there was no information ). Which is why I bought Astra bottom ball joints.

I gave up that build due to a number of issues and sold the chassi.. I got an email last year from the guy that bougt the bits saying he needed a quick letter to state the chassis was new as he was about to register the car

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #16  
Old 10th January 2010, 04:12 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

Which was the question i was asking. is the taper the correct angle. Seems there is some doubt..

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #17  
Old 10th January 2010, 07:34 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

Anyone got one to measure then?

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #18  
Old 10th January 2010, 08:34 PM
RAYLEE29's Avatar
RAYLEE29 RAYLEE29 is offline
Senior Member
 
Join Date: Sep 2008
Location: POOLE DORSET
Posts: 520
Default

I used the 19mm Axminster one set up in the pillar drill and kept cutting and checking till i was happy with the fit basiclly full nut and washer of thread sticking out the top and the largest bit of the taper just visible below the upright.
The taper is a good enough fit that after only tightening a little the need to be tapped to get back off.
Ray
__________________
Total spend so far £1116.08
1ST ALBUM HERE
2ND ALBUM HERE
Reply With Quote
  #19  
Old 10th January 2010, 08:53 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,389
Default

That still does not answer the question though. Is the taper of the axminster reamer the correct angle to match the ball joint taper?

The taper on the joint should be paralel to the taper in the hole otherwise there will be a loose fit at one end or the other.

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #20  
Old 10th January 2010, 09:09 PM
Davey's Avatar
Davey Davey is offline
Senior Member
 
Join Date: Dec 2009
Location: Telford
Posts: 1,040
Default

A couple of points are coming to light here, firstly the question of the correct taper, I'm using Granada uprights and I'll check them for the taper before I go reaming anything out. Secondly is a comment someone made about using a reamer, you do not use it like a tap. You should never turn a reamer backeards as it blunts the cutting edge. With a tapered reamer you simply lift it out of the hole every so often while turning it forwards.

D.
__________________
visit my website at www.cossie.davenewell.co.uk
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 07:52 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.