Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Chassis
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 29th June 2009, 08:08 PM
chriseyj chriseyj is offline
Senior Member
 
Join Date: Feb 2009
Location: Derbyshire
Posts: 121
Default Steering rack supports

Hi just a quick question.
Should the steering rack supports cp19 & cp20 be 285mm apart or 288mm.
The book states the mounting hole centres should be 258mm apart but if you add the differece from either side to this, 30mm you get 288mm from edge to edge, not 285mm.

Have seen this asked before but didn't see a definate answer.

Thanks Chris
Reply With Quote
  #2  
Old 29th June 2009, 08:24 PM
HandyAndy's Avatar
HandyAndy HandyAndy is offline
Senior Member
 
Join Date: Jan 2009
Location: cleveland
Posts: 3,917
Default

they need to be placed so that they are lined up with your steering column & also so that the column goes thru the bearing support plate (CP16) centrally, hope that makes sense???

andy
__________________
Flat Pack Chassis Kits for sale, contact me at andyroadster@yahoo.co.uk
Reply With Quote
  #3  
Old 29th June 2009, 08:26 PM
HandyAndy's Avatar
HandyAndy HandyAndy is offline
Senior Member
 
Join Date: Jan 2009
Location: cleveland
Posts: 3,917
Default

DOH, silly me i thought we were talking about the steering WHEEL supports CP15,s.. sooooorrrry

long day & an all that.

andy
__________________
Flat Pack Chassis Kits for sale, contact me at andyroadster@yahoo.co.uk
Reply With Quote
  #4  
Old 29th June 2009, 08:31 PM
HandyAndy's Avatar
HandyAndy HandyAndy is offline
Senior Member
 
Join Date: Jan 2009
Location: cleveland
Posts: 3,917
Default

right i,ll try again

if i remember correctly, when i welded in these plates i had a few mm over which i think came from the measurement 288mm,
so if you have your steering rack available make sure the rack fits into the support & that you can get the fixing bolts thru, i had to widen the slots a little & grind a bit off the edge of the supports to make it fit snugly.

hope thats better info than my first attemp,

andy
__________________
Flat Pack Chassis Kits for sale, contact me at andyroadster@yahoo.co.uk
Reply With Quote
  #5  
Old 29th June 2009, 08:37 PM
Spikehaus Spikehaus is offline
Senior Member
 
Join Date: Aug 2008
Location: Plymouth, Devon
Posts: 484
Default

Have you done a search for the book ammendments, I sure Chris did a new drawing for this. The only problem I remember was the angles not add up. I did not check the whole centres, but the plates can only be the same distance apart as the diagonal brace.
Reply With Quote
  #6  
Old 29th June 2009, 08:39 PM
chriseyj chriseyj is offline
Senior Member
 
Join Date: Feb 2009
Location: Derbyshire
Posts: 121
Default

Thanks for your reply, I haven't got a rack yet which is a bit of a pain else I'd of measured between the mounting holes. The diagonal brace cp21 that goes between them is 228 I noticed, if you add 60mm, the width of both cp19 & cp20 plates, you would also get an edge to edge width of 288mm.
Looks like the book migth be wrong and it should be 288mm, guess i'll be repositioning them tomorrow.
Reply With Quote
  #7  
Old 29th June 2009, 08:41 PM
chriseyj chriseyj is offline
Senior Member
 
Join Date: Feb 2009
Location: Derbyshire
Posts: 121
Default

Spikhaus, was yours ok using the standard brace width of 228 on the diagonal?

P.S the steel bush inner tubes I bought from you were great.

Last edited by chriseyj : 29th June 2009 at 08:44 PM.
Reply With Quote
  #8  
Old 29th June 2009, 08:48 PM
Spikehaus Spikehaus is offline
Senior Member
 
Join Date: Aug 2008
Location: Plymouth, Devon
Posts: 484
Default

Looks like we all tumble on the same mistakes, maybe I will compile a list of common mistakes for the new builders to use as check list. Its all part of the learning curve and building what is a new an improved chassis. I will add this dimension to my book that now has some much pen and grinding dust on, I can hardly see the drawings.

Still, I also hold it as my build Bible as it has given a lot of pleasure and consumed my life for the last year. Maybe one day I will get round to reading it. By trade, drawings and NBS spec are everything!
Reply With Quote
  #9  
Old 29th June 2009, 08:51 PM
chriseyj chriseyj is offline
Senior Member
 
Join Date: Feb 2009
Location: Derbyshire
Posts: 121
Default

I take it you agree they should probably be 288mm apart? glad i only tacked them lightly on one side.
Reply With Quote
  #10  
Old 29th June 2009, 09:00 PM
Spikehaus Spikehaus is offline
Senior Member
 
Join Date: Aug 2008
Location: Plymouth, Devon
Posts: 484
Default

I almost postive this is correct. I am going to have to go and calulate the geometry now or I will not sleep tonight!

Quote:
Originally Posted by chriseyj View Post
Spikhaus, was yours ok using the standard brace width of 228 on the diagonal?

P.S the steel bush inner tubes I bought from you were great.

Last edited by Spikehaus : 29th June 2009 at 09:06 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 10:23 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.