Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Donor cars
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 11th June 2008, 11:54 PM
eirekev eirekev is offline
Junior Member
 
Join Date: Jun 2008
Posts: 1
Question Confused!! What engine

Im new to this and im looking for information before i go off and build my first car. With the roadster what specifications does the engine have to be to fit the haynes design???(does it have to be RWD etc)

I was thinking about a honda vtec engine but looking through the forum they dont work with this design.

Im looking for something with fast acceleration so any suggestions??
Reply With Quote
  #2  
Old 12th June 2008, 12:41 AM
3GE Components's Avatar
3GE Components 3GE Components is offline
Senior Member
 
Join Date: Jul 2007
Posts: 370
Default

Audi 5v turbo?

http://www.haynes.co.uk/forums/showt...highlight=audi

__________________
Quality parts for the Haynes Roadster - manufactured to a standard, not down to a price.

Contact us at component-sales@hotmail.co.uk or visit our website www.3gecomponents.com
Reply With Quote
  #3  
Old 12th June 2008, 08:32 AM
Alphax Alphax is offline
Junior Member
 
Join Date: Apr 2007
Location: The Netherlands
Posts: 19
Default

The Vtecs are expensive engines to find, really expensive to repair, expensive to tune and the gearbox is noisy. But it does give you good power and high rpm.

Audi turbo is a very suitable alternative.
__________________
Cheers

Frans

Alphax Kitcars: mainlands official Roadster dealer.

see www.alphax-kitcars.com
Reply With Quote
  #4  
Old 13th June 2008, 01:54 PM
Neil P Neil P is offline
Member
 
Join Date: Mar 2007
Location: East Yorks
Posts: 80
Default

You guys are so predictable.
Reply With Quote
  #5  
Old 18th June 2008, 12:22 PM
bobbyh bobbyh is offline
Senior Member
 
Join Date: Jan 2008
Location: Stourbridge
Posts: 249
Default

hayabusa engine expensive but bike enige all the way
Reply With Quote
  #6  
Old 18th June 2008, 06:01 PM
spalders spalders is offline
Junior Member
 
Join Date: May 2007
Posts: 15
Default engine choices

Neil,

Had a look at your flickr site - your build looks really interesting. I notice that you have made an adaptor plate 4AGE - MT75 gearbox. Was this straightforward, I am thinking of doing the same. Here's one for the Toyota engines!

Spalders
Reply With Quote
  #7  
Old 18th June 2008, 09:34 PM
Neil P Neil P is offline
Member
 
Join Date: Mar 2007
Location: East Yorks
Posts: 80
Default

Spalders,

not exactly straightforward and at the moment untested. Someone told me it was too difficult to do, so I had to!

I measured the engine to establish centres etc and drew up a template incorporating the gearbox measurements from the MT75 plans on this site. I had it laser cut locally from 6mm steel.

The starter needs locating to the other side, one of the difficulties being that it is fixed with bolts from the rear rather than locating onto studs with nuts etc. The bellhousing is relieved in various places to allow for bolt heads and the starter.

The clutch fork pivot needs lengthening to bring it closer to the clutch assembly, it needs a spigot bearing fitting and the sierra clutch plate is a snug fit in the pressure plate side. I had to file off the small lugs (about 2mm) from the outer edge to give clearance.

The clutch engages and disengages but as the engine is not yet running it is still a bit of an unknown quantity. It would probably have been far easier to buy a type 9 conversion or fit a ford motor but I had the MT75 and quite like a bit of a challenge. I also like the Toyota motor because I can fit it using all the original ignition and fuelling kit, it makes reasonable power and revs well.

The engineering is more function over form. Straightforward - not really, but quite satisfying when it comes together.

I have some more photo's of the plate etc, I'll put them on over the next few days if you want to have a look.

Oh, eirekev, my understanding is that due to the weight (or lack of it) they go pretty well whatever you put in them. I'm going for lighter weight rather than huge power.

Neil
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 10:11 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.