Book Amendments & Extra Guides

[AshG]

Here are the guides that used to be on the fourm before the melt down.

I have hosted them until Chris gets back round to doing a new sticky

Book Amendments
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/BYOSC_amendments_1.4.pdf

Front Frame Guide Part 1
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/front_frame_guide_part1.doc


Front Frane Guide Part 2
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/front_frame_guide_part2.doc


Front Frame Part 3
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/front_frame_guide_part3.doc


Rear Lower Wishbone Revised Design
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Roadster_Rear_Lower_Wishbone.pdf


Rear Upper Wishbone Revised Design
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Roadster_Rear_Upper_Wishbone.pdf


Steering Rack Support Revised Drawing
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/steering_support.pdf


Left Hand Drive Chassis Drawings
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Left_Hand_Drive_Chassis.doc


MT75 Chassis Drawings
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/MT75_Gearbox_Transmission_Tunnel_Mods.doc


Seat Back Diagonals Tutorial
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Seat_Back_Diagonals.doc


Shorter Pedal Box Drawings
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Shorter_Pedal_Box.doc

E Mark Meanings for lights
http://www.haynesroadster.pwp.blueyonder.co.uk/haynesForum/Codes.pdf

VIN Letter To send to Dvla
http://www.haynesroadster.pwp.blueyonder.co.uk/vinletter.doc

[mr henderson]

Well done, I'm sure there are many who will find that very helpful

[Land Locked]

Ash, many thanks for these.

Just one question, are there meant to be diagrams in the front frame guides? If so am I the only one who can't see them?

[AshG]

there are diagrams. what version of word are you using to open them?

[Land Locked]

Using open office on Linux, explains it all though. Thanks.

[AshG]

i wl make them pdf format in the morning for you

[alga]

Using open office on Linux, explains it all though. Thanks.

I see the diagrams just fine, OpenOffice.org 3.0.1 on Ubuntu Jaunty.

[Land Locked]

i wl make them pdf format in the morning for you

Hi Ash, I'd really really appreciate that.

Alga, I'm using the last long term support version from mint, which puts my open office at about ver 2.5. I don't normally need to be on the bleeding edge, I only went Linux to get away from Windose.

[AshG]

realised what was wrong. i saved them in word 2007 format .docx . have now saved them in word 97 format .doc

if you download them again they should now work on your older version of open office.

[Land Locked]

Many thanks Ash. I can see the diagrams again :D

[Balidey]

In the book amendments PDF, are the last 2 pages blank, or is it just on my PC?

[Land Locked]

In the book amendments PDF, are the last 2 pages blank, or is it just on my PC?

I see them blank too.

[AshG]

i believe that they are meant to be blank. i think chris just forgot to delete the extra pages before he made the pdf.

[Chris Gibbs]

I'll get these reposted and stickied asap

Cheers

Chris :)

[Adam R.]

question about FF3

in "Front Frame Guide Part 1" we have got FF3 359.5
in book at 162site we have FF3 320

which one is correct ?

[alga]

Does anyone have the guides on MT75 variation and LHD perchance?

[alga]

question about FF3

in "Front Frame Guide Part 1" we have got FF3 359.5
in book at 162site we have FF3 320

which one is correct ?

Note that 320 in the book is the length of a projection parallel to the longer leg of the pipe after the bend. The cut length is 290 + 69.5.

[TOLiSGR]

Hello all, I've downloaded the 'tutorials' for myself when I first saw them, so here they are!

(sorry for being late posting, I was in the army for a few days)

Files are in Rapidshare because of the forum's size limit

Front Frame Construction Tutorial.doc (http://rapidshare.com/files/269753064/Front_Frame_Construction_Tutorial.doc)

Left Hand Drive Chassis.doc (http://rapidshare.com/files/269753065/Left_Hand_Drive_Chassis.doc)

MT75 Gearbox Transmission Tunnel Mods.doc (http://rapidshare.com/files/269753066/MT75_Gearbox_Transmission_Tunnel_Mods.doc)

Seat Back Diagonals.doc (http://rapidshare.com/files/269753067/Seat_Back_Diagonals.doc)

Shorter Pedal_Box.doc (http://rapidshare.com/files/269753068/Shorter_Pedal_Box.doc)

Original Tutorial Pics (http://rapidshare.com/files/269753512/Tutorial_PiCS.rar)

[AshG]

cheers tolisgr.

i will download them and host them properly as rapid share is a bit of a pita.

[TOLiSGR]

Thanks mate! :)

[AshG]

left hand drive chassis drawings added

[Janne E]

Thanks Ash:D

Janne

[John.W]

Is anybody else having problems downloading the files from rapidshare, I am trying to download the changes for the mt75 box

[mr-p]

Yeah me too Handyandy just sent me the PDF of the mods in an email PM me your email address & i will forward it on

P.

[HandyAndy]

Yeah me too Handyandy just sent me the PDF of the mods in an email PM me your email address & i will forward it on

P.

beat me to it :D

andy:)

[AshG]

hi guys sorry sorry I forgot to add them to my web server.

they all should now be at the top of the page so you don't have to cock about with rapid share.

Ash

[John.W]

Thanks Ash and Mr p Just printed the updates off.
I am a bit confused about the wishbone drawings because there doesn't appear to be any difference between the ones in my book and the ones i've just printed. Or am I just being stupid!!!!

[alga]

You must have the second printing which has the error corrected. Too bad it's not marked as an updated edition.

[mr-p]

Can anybody shed a bit of light on this for me?

On the attached doc for the MT75 tunnel mods.

The drawings which show MT10 & MT12 on plan are the 160 & 187 dims from center to outside of tube the wrong way round??

I have looked at this a few times & still cant get my head round it, the sections & the plans show the short side on the passengers side & the drivers footwell at 164mm. The way MT10&12 are drawn would suggest otherwise??

Or am I being thick:confused:


P.

[Bonzo]

I can't really help on the MT75 mods as mine was a type 9 chassis :)

Is it possible that you are looking at the LHD version of the MT75 mods :eek: :D :D

[mr-p]

Cheers Ronnie,

Thats a thought but ive just checked & teh dims for the modded pedal box match up, it appears they are miss matched in the same document.

Might have been a cut & paste error or something?? LHD details on the RHD doc??

[jimmy wonder]

i cant get 3 of the links to work,is it my computer or are they broken?front frame guide parts 1.2 and 3.

[tkpm]

I have just tried them and they worked fine, must be your computer.

Terry

[twinturbo]

i cant get 3 of the links to work,is it my computer or are they broken?front frame guide parts 1.2 and 3.

Do you have MS Word Installed? Or Open Office?

TT

[stephanedu14]

Hello has all.
I have just discovered this subject on the forum of kit-car French.
Superb bonds on the details of the frame, of conversions left right-hand side of the driver's cab
and the modification of the tunnel of limps has speed.
Can be possible to put this post in permanent top of list of the family of the frame.
Cordially.

[Rosco]

Just for future reference, it looks to me like the jig drawings for the rear hub and the rear lower wishbone are wrong and should be back worked from the part drawings

[voucht]

A shame the hosting server from Ash no longer works... they were precious documents.

I had downloaded 2 of the documents when I was building my car, including the book amendments. I put them on my Google Drive server for public access.

https://drive.google.com/drive/folders/0B-iOekLVikV5c2xSRXZCdElrSEU

But I miss most of the documents from the old Book Amendments & Extra Guides (https://haynes.co.uk/forums/showthread.php?t=2430) section.

Does anyone have them, so we can gather them in one place ?

[H-L-Smith]

A shame the hosting server from Ash no longer works... they were precious documents.

I had downloaded 2 of the documents when I was building my car, including the book amendments. I put them on my Google Drive server for public access.

https://drive.google.com/drive/folders/0B-iOekLVikV5c2xSRXZCdElrSEU

But I miss most of the documents from the old Book Amendments & Extra Guides (https://haynes.co.uk/forums/showthread.php?t=2430) section.

Does anyone have them, so we can gather them in one place ?

I have all of them except for the last two on Ash's initial list. I show they were created on my system in February of 2011, which is likely when I downloaded them. I can't be absolutely positive they are the very latest versions, but they likely are.

Message me with your e-mail address and I'll send them to you.

Regards,

Lonnie

[PorkChop]

Sylvain, I have the lot backed up.

I also seem to have...


a number of Vodou tech drawings/chassis cut lists when Matt Barrett made them available in 2011
some additional notes on the SSC MX5 version that I made myself, based on what was listed in SSC's webstore when Andy was around (e.g. damper/spring specs)
technical drawing for chassis changes to accept SSC GRP rear panel

[voucht]

Hi,

Thanks to PorkChop and the documents he sent me, I have completed the list of "book amendment" documents my Google drive public section. Access is public.

https://drive.google.com/drive/folders/0B-iOekLVikV5c2xSRXZCdElrSEU

[Rosco]

Sylvain, pm me your email and i will send you my roll cage drawings, you can share them for others to

[voucht]

Now Rosco's roll cage drawings are also available from the same link, the folder containing the documents is called "Rosco's roll cage".

Rosco specifies: "I bent the rear hoop to the book dimensions out of 50mm and did the rest out of 45mm, im 5ft 10 and theres room for a helmet etc, side mounts can be seen in my build thread (https://haynes.co.uk/forums/showthread.php?t=13517)"

Thank you !

[Rosco]

Side mount pictures on this page

https://haynes.co.uk/forums/showthread.php?t=13517&page=17

Any questions just ask me

[Ricky]

Hi just want to find out do the book amendments and guides not work anymore ? They don't seem to be working

[voucht]

Hi Ricky,

If you go up 4 posts on this thread, my post #40 gives the link to my google drive folder (public access) where theses files are now hosted:

https://drive.google.com/drive/folders/0B-iOekLVikV5c2xSRXZCdElrSEU

Hope this will help :)

[Ricky]

Thanks alot really appreciate it