Hi David:)
I took some photos but not sure if they will help. If you want I can take some measurements.
Here's the photos....










Hope that helps if not give me a shout...

Sorry went to edit the post then lost tinternet, joys of living in the sticks. If you fill in the gaps a,b,c,d from the leading edge round the curve and join to the bottom of the rear panel that is how these things are intended to work, well in theory at least.

Hi all,
Well managed to get my rear under floor/diffuser finished. I took notice of what Phil said and with a bit of tinkering I ended up with this. All inlets are now smaller than the outlets.
I've also drilled quite a few 60mm diameter holes to help remove some of the air built up in the rear tub.





As you can see in the next photo some of the air built up in the rear tub can be released above the diffuser in the slot I've created.






I also decided to make angled cover plates for my lower wishbones while I was at it, should now clear on full droop...

Sorry more photos.
I'm now at the stage where I'm now removing stuff to fit parts for good... and boy that's a good feeling...LOL...
I removed my rear tub to tidy my electrics and just finish stuff off.





Now all suspension bolts are in place along with springs on the dampers. Also fitted the diif rubber washer thingy's.

Bye for now....;)

Hi everybody,:)
Well judging by my last post I'm classed as "MIB"......(Missing In Build).:eek:
Basically work went bonkers and left no time for car. I decided to keep away from forum for a while in case I was tempted to use the little spare time I had working on the car again.
My son had taken up football and daughter shows horse at weekends and missus wanted kitchen renewing so I decided to spend time with the family.
I should have scored enough brownie by now to soon get on with it again.

Hope to speak to you all soon with some photos... fingers doubly crossed..:D

I'm glad your back, I'd been missing your build porn.

Car For Sale
 

Unfortunately due to lack of time car for sale. Details on build thread, plus other bits not seen. £2,500.00 to a good home, no offers.

Sorry to hear you are selling up. Can't you just store it until you have got time. It will be worth it in the end. Even of that's 5 years down the track.

You have put so much hard work into your build

David

Don't do it mate:( .....cover it up and walk away for a bit, that happened to me a few times, it made restarting it feel a lot better even in little chunks. One thing is for sure your car would be up there at the top in terms of value so think of it as an investment.....here's hoping you reconsider.

I agree, if you don't need the money, put it in a corner and forget about it. I think you'll regret selling it one day.

Don't do it Johno, yours is a hugely inspiring build. Like Kev said, store it if you can and come back. Its too good to sell part finished :(

Please, don't sell it!

Good Home Required....
 

Thanks everyone for your replies, I completely understand what you are saying but times and circumstances have changed for the foreseeable future. I have made a decision to spend more time with my family without having something like this to distract me.
I now spend more time away from home than I like and the time that I do have I spend doing things with my children.
OK now down to business...

SPECIFICATIONS/PARTS
Front and rear suspension fully adjustable with rose joints and poly bushes powder coated black. Front suspension also has built in camber adjustment.
Protech shock absorbers with springs front and rear.
Front and rear brake calipers sand blasted and painted black.
New front and rear brake discs and pads fitted.
Fuel lines and electrical wiring fitted front to back.
Aluminum fuel tank fitted and plumbed in.
New handbrake cables and handbrake fitted.
Clutch, brake and accelerator pedals fitted and plumbed in.
Engine painted and fitted, differential painted and fitted and prop shaft shortened and balanced and fitted.
New battery fitted and connected.
New radiator, cooling pipes and expansion tank plumbed in.
New air inlet filter fitted.
Dashboard and instrument cluster made and ready for installing.
Drivers seat with 4-point harness.
Rear diffuser painted black.
Rear equinox wings ready to bolt on.
Front Westfield wings in black.
Front SVC headlights.
Front indicators installed.
AGM bodykit fitted.
Full stainless steel exhaust system fitted.
and many more etc.....

Anyone interested please look on this build thread for photos.

Special Christmas price of £1750.00 ONO.

If you are interested please reply on this thread as it will come through to my phone.

At some time in the future when I have more time available I will probably start a new build.

I would like to think someone on here would be interested as I know it would go to a good home.

Thanks Johno

You could answer your PMs Johno ;) :p

That for nowt mate.... surely your hand has been snapped off by now jeezzz

I thought about it, do I really need two nearly finished builds?, one at home, one up north at the GFs...... mmmmmm tempting.
How much £ do you think it needs on parts to get it finished?

Hi all,
I've really enjoyed building the car and learning a lot and it's been fun talking to all you guys :) .
Basically since my father passed away I have felt the need to spend all my free time with the children hence the reason at the moment for moving on.

What's left to do on the car....
Purchases
Seat (Kit parts direct) £100
Harness £90
Rear lights £100
Flexible brake pipes.
To be honest I think that's pretty much it.

Thanks johno, I know I shouldn't but am temped, does it start and roll? Which Luton are you, near Peterborough?

Hi Mike,
Haven't started it yet but donor car was a runner before putting it in Roadster.
I'm live in Lutton near Spalding Lincolnshire about 30 miles from Peterborough.