Help, lost me nuts..
 

HELLLLLLLP....

I'm in desperate need of a couple of nuts for the Maxi balljoints.
Has anyone got a couple or could get them for me?
Just about ready to put the car back on its wheels.
But bu*****d without the nuts.

I've looked everywere for mine.
I've even tried...........tidying up..:eek:
The only thing I can think of is I left them in the
UK last trip.

Hi David

Did we ever get to the bottom of what size they are :confused:

If I can get replacements easy enough .... Quite happy to send over mine ;)

I won't be needing them for quite a while yet :o

Do you still need a plug for that Ford Ka clock of your's ? .... I just hapen to have aquired a spare when I got a clock from the breakers the other week :)

Hi Ronnie.

I'm afraid I have no idea what thread they are.
That's what has left me a bit stuck, I can't even order them.
If anyone does know what thread they are, maybe they could let us know.

If no one comes up with an alternative, I'll take you up on your offer.
I can get them replaced when I get back to the UK.
Just there is nowhere around here to get anything like that.


As for the Ka clock, I've now soldered the wires on so don't need a plug.
Cheers anyway

If nothing turns up David .... Pm me your address & will post them off PDQ :) :)

There was a thread a while back .... But I don't think we ever got to the bottom of the thread type & size. :confused:

Probably got spares in my huge collection of old Imperial stuff anyways ;)

Ronnie, just sent you a PM.

If anyone else has a couple of Maxi ball joint nuts they are not actualy going to use, I desperatly need them.

Cheers

If they are defo 1/2" unf then I'm saved...
http://cgi.ebay.co.uk/1-2-UNF-NYLOC-...item56379a12d4

Anyone else confirm that size?

How big are Davids nut's
 

When we had the thread going a little while back .... I put the Vernier & thread gauge on mine .... I came to the size of 1/2" UNF !!

Some folk thought it likeley that they were M12 metric fine .... Tried a known metric fine nut on one of mine & it didn't fit.

If I had to lay a £10 note on the line .... I would plump for the UNF option :)

If I had to lay someone else's £10 on the line ..... I'd choose both :D :D

Think they are M12x1.25, I have a couple in spare so just sent me your adress and I can put them at the post to you...

I have checked the thread two times but I can try theme again when I got home today just to be sure:)

Janne

Cool Janne :cool:

Between us, we'll have David's nuts covered :eek: :D

I've put a thread gauge on them and they look like m12 x 1.25 to me also .

I think i have a pack of 1/2 UNF nuts lying around when I lost mine a few months ago - will check tomorrow and get back to you.

I just checked and it´s M12x1.25 my balljoints come from Rally Design so it should be the same.
I have M12x1.25 locknuts so just let me know if you want me send them to you.

Janne

Now I am confused....:rolleyes:
I found a nut today that fitted,
but when I tightend down on it it stripped out.

So I now know there is a nut with a close thread.
I am tempted to plump for the 1/2"UNF nuts on Eblag.
Then if they are wrong at least I now then that they are M12's
And will still have time to get them shipped out.

BTW aint M12x1.25's wheel nut size?

Thanks for all the offers and replies guys.
That's what makes this such a great forum..:)

I tested 1/2 UNF and it was close but not right..

Janne

Wheel nuts are usually M12x1.5, but the wheel shops stock M12x1.25 too, so some cars must use it as well.

Thanks for all the help guys.
Janne is going to post me down a couple of M12's
So all being well I'm now covered.
Thanks Janne..:D