Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Engine/transmission
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 9th December 2016, 12:02 PM
Dave F's Avatar
Dave F Dave F is offline
Senior Member
 
Join Date: May 2011
Location: Wakefield
Posts: 124
Default MX5 Cooling & Rad

I'm looking at buying a Radiator over the next week or so and was looking at the options. My initial plan is to use an 190e (http://www.ebay.co.uk/itm/122141245444?_trksid=p2060353.m1438.l2649&ssPageNa me=STRK%3AMEBIDX%3AIT) I believe it gives better cooling than the polo Rad. Looking at it though it has a top and bottom pipe but no small top pipe. I plan to use a polo header tank that will be T'ed into the back of the engine where the heater matrix would normally be but where would the top 'overflow', if that is actually what it is, go? I hope this all makes sense and I always open to any other options
__________________
God loves a trier

Actual cost so far = Have chosen to stop counting incase I incriminate myself -
Cost ive told the wife = A hell of a lot less than I have spent. -
Reply With Quote
  #2  
Old 10th December 2016, 01:07 PM
Ianr Ianr is offline
Senior Member
 
Join Date: Sep 2014
Posts: 252
Default

I used the polo header tank T'd into the heter matrix loop at the rear of the engine and a golf radiator which does not have a small pipe similar to the merc one. I put in a straight 32mm? from memory which has an 8mm take off which I connected the small pipe to. I actually used 8mm copper from the header tank with very short 8mm flexi rubber pipes to connect each end
__________________
My build blog here http://ianhaynes20.wordpress.com
Reply With Quote
  #3  
Old 10th December 2016, 02:20 PM
Dave F's Avatar
Dave F Dave F is offline
Senior Member
 
Join Date: May 2011
Location: Wakefield
Posts: 124
Default

Quote:
Originally Posted by Ianr View Post
I used the polo header tank T'd into the heter matrix loop at the rear of the engine and a golf radiator which does not have a small pipe similar to the merc one. I put in a straight 32mm? from memory which has an 8mm take off which I connected the small pipe to. I actually used 8mm copper from the header tank with very short 8mm flexi rubber pipes to connect each end
So is it T'ed into the top rad pipe, that's what I was thinking but not sure if the system would function as it should.
__________________
God loves a trier

Actual cost so far = Have chosen to stop counting incase I incriminate myself -
Cost ive told the wife = A hell of a lot less than I have spent. -
Reply With Quote
  #4  
Old 10th December 2016, 05:01 PM
Cropper Cropper is offline
Member
 
Join Date: Jul 2013
Posts: 92
Default

Dave
If you check out this photo it shows how I did mine with the 190e rad & polo header, works fine.
https://flic.kr/p/znQChn
Reply With Quote
  #5  
Old 10th December 2016, 05:45 PM
Dave F's Avatar
Dave F Dave F is offline
Senior Member
 
Join Date: May 2011
Location: Wakefield
Posts: 124
Default

Quote:
Originally Posted by Cropper View Post
Dave
If you check out this photo it shows how I did mine with the 190e rad & polo header, works fine.
https://flic.kr/p/znQChn
By the looks of it, your Rad has the top pipe, all that I have seen don't, or am I missing something?
__________________
God loves a trier

Actual cost so far = Have chosen to stop counting incase I incriminate myself -
Cost ive told the wife = A hell of a lot less than I have spent. -
Reply With Quote
  #6  
Old 10th December 2016, 06:39 PM
Cropper Cropper is offline
Member
 
Join Date: Jul 2013
Posts: 92
Default

Sorry I should have said, it is just a pipe connector that I dust tapped & epoxied into place. The plastic end caps are soft enough for the connector to make its own thread if you just drill the hole undersized & work it in slowly. Mine actually tightened ok but I put it in finally with some epoxy glue for safe measure. Hope this helps
Reply With Quote
  #7  
Old 11th December 2016, 10:18 AM
Ianr Ianr is offline
Senior Member
 
Join Date: Sep 2014
Posts: 252
Default

Quote:
Originally Posted by Dave F View Post
So is it T'ed into the top rad pipe, that's what I was thinking but not sure if the system would function as it should.

Yes that's correct - and it seems to work fine with the fan cutting in after being stationary for what seems ages and then cutting out shortly after (standard MX5 fan)
__________________
My build blog here http://ianhaynes20.wordpress.com
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 05:38 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.