Riveting Floor - Haynes Forums

chriseyj Riveting Floor 1st July 2009, 04:39 PM

deezee I think (I've written it down... 1st July 2009, 05:43 PM

chriseyj Thanks for the reply, that... 1st July 2009, 06:07 PM

AshG i have done a 1.5mm ali floor... 1st July 2009, 06:41 PM

deezee I've used 2mm aluminium (5000... 1st July 2009, 07:39 PM

Tilly819 I used 1/8th alluminium pop... 1st July 2009, 10:16 PM

chriseyj Thanks for the info might get... 2nd July 2009, 12:29 PM

deezee You do the floor, then the... 2nd July 2009, 03:51 PM

chriseyj I was thinking of having a... 2nd July 2009, 04:26 PM

Chris_ Dont forget a nice gob of... 2nd July 2009, 08:18 PM

Peter-C Will these rivets do for the... 8th January 2010, 12:58 PM

dogwood I'm just sorting an order out... 8th January 2010, 01:14 PM

flyerncle £1 11s and sixpence :p And... 8th January 2010, 01:19 PM

dogwood ooops....:D Rivet. 8th January 2010, 01:25 PM

flyerncle So long as it's not the... 8th January 2010, 01:31 PM

HandyAndy well David is an ex seafarer... 8th January 2010, 01:33 PM

dogwood Yea, never did find... 8th January 2010, 01:34 PM

flyerncle I knew that and reason for... 8th January 2010, 01:36 PM

dogwood Lucky for my bot bot:rolleyes: 8th January 2010, 01:40 PM

HandyAndy i,m havin a FAG .....i mean... 8th January 2010, 01:44 PM

flyerncle I knew what you meant ! On... 8th January 2010, 09:10 PM

HandyAndy i thought the same but then... 2nd July 2009, 08:56 PM

chriseyj Cheers Andy I was going to... 2nd July 2009, 10:05 PM

HandyAndy well the way i look at this... 2nd July 2009, 10:12 PM

chriseyj Just wondering Andy what size... 2nd July 2009, 11:09 PM

HandyAndy i,m using the same as Ash G... 2nd July 2009, 11:17 PM

chriseyj Do you think those rivets... 2nd July 2009, 11:25 PM

HandyAndy yes i think they will, to be... 2nd July 2009, 11:39 PM

AshG crazy fool. i just make it... 3rd July 2009, 12:59 AM

HandyAndy :D :D well if my floor falls... 3rd July 2009, 01:03 AM

flyerncle Ash,Where can you get cleco's... 3rd July 2009, 03:48 PM

Jezzer99 I bought my cleco kit from... 3rd July 2009, 04:54 PM

Beardy_John I've always found it strange... 3rd July 2009, 09:03 PM

AshG i got my clecos from las... 5th July 2009, 11:52 AM

AshG here you go link for pliers... 5th July 2009, 11:54 AM

AshG 1/8 is 3.2mm 5th July 2009, 11:54 AM

AshG By the way car builder... 5th July 2009, 12:01 PM

HandyAndy just a quick note, i suppose... 2nd July 2009, 11:47 PM

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode