Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > Engine/transmission
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 10th December 2009, 12:08 AM
Rik178m Rik178m is offline
Senior Member
 
Join Date: Feb 2009
Posts: 121
Default

http://www.locostbuilders.co.uk/view...message=non e

Maybe of interest??
Reply With Quote
  #12  
Old 10th December 2009, 07:18 PM
davidimurray's Avatar
davidimurray davidimurray is offline
Senior Member
 
Join Date: Jan 2009
Location: Near Cardiff
Posts: 742
Default

Personally - I would say continue with the CVH. You will have a known good engine, you will learn loads about engines and rebuilding them, you will have a big smile on your face at the end. Also a lot of the itmes you list you will probably need for the Zetec route anywya, or while the engine was out of the car you would be tempted to do some bits - e.g.

• Engine degreaser - £5
• Engine paint - £6
• Oil - £20
• Spark Plugs - £10
• Thermostat - £5 - possbily while you've got the chance
• Oil filter - £5
• Timing Belt - £10 - possbily while you've got the chance
• Sump Gasket - £8.46 - does the sump need chopping on the Zetec?
• Air Filter
• HT Leads - £12 - depends on your ignition setup

Also worth shopping around for prices on bits - head gasket sets look to be on ebay for about £20
Reply With Quote
  #13  
Old 10th December 2009, 07:44 PM
Tatey's Avatar
Tatey Tatey is offline
Senior Member
 
Join Date: May 2009
Location: Leicester
Posts: 827
Default

I have to say i think i am leaning more towards the CVH sides of things due to:

a) More of an experience rebuilding it
b) I'm a poor student at the moment, so the cheaper it is the quicker i can get it on the road
c) I'll be recycling
d) It will be a better step-up since I'm an inexperienced driver
e) I can always upgrade in the future
f) Satisfaction of getting a non runner running.
g) I can spread the cost over a much longer period.

But i've still got a while to decide as i'll be finishing my chassis, making wishbones/uprights and then getting the car rolling, so i may change my mind again
__________________
1.8 Silvertop Zetec (ZX6R Carbs + Megajolt) + Type 9

My Build Blog: http://www.haynes.co.uk/forums/showthread.php?t=2736 - Last Update: 31st October 2020

Total Spent so far: Stopped counting
Reply With Quote
  #14  
Old 10th December 2009, 08:48 PM
thwang thwang is offline
Member
 
Join Date: Sep 2008
Posts: 84
Default

personlly i would rebuild the engine you have as lest you know its a good engine.my mate at works just bought a new engine for his focus from a chap in doncaster breakeryard it was sold as a goodun but its foobard and the guy wont give him his money back or accept the engine back
Reply With Quote
  #15  
Old 10th December 2009, 09:15 PM
Land Locked's Avatar
Land Locked Land Locked is offline
Senior Member
 
Join Date: Apr 2009
Location: Johannesburg, Sarf Efrika
Posts: 232
Default

Quote:
Originally Posted by Tatey View Post
I have to say i think i am leaning more towards the CVH sides of things due to:

a) More of an experience rebuilding it
b) I'm a poor student at the moment, so the cheaper it is the quicker i can get it on the road
c) I'll be recycling
d) It will be a better step-up since I'm an inexperienced driver
e) I can always upgrade in the future
f) Satisfaction of getting a non runner running.
g) I can spread the cost over a much longer period.

But i've still got a while to decide as i'll be finishing my chassis, making wishbones/uprights and then getting the car rolling, so i may change my mind again
I find points A,C,F&G really appealing. There's a huge amount of satisfaction to be had from making a non runner run. I'm on a tight budget myself and being able to spread the cost over a longer time is important.
__________________
Regards (The mad Sarf Efriken)
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 07:44 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.