Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > General discussion
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #501  
Old 7th June 2013, 01:39 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,393
Default

Not done HomeBrew in 10 years, but with the brother in law moving just 100yards down the road, and having a house to himself... I think we will be starting our own brewing company.

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #502  
Old 7th June 2013, 02:27 PM
jps jps is offline
Senior Member
 
Join Date: May 2012
Location: Colchester, Essex
Posts: 439
Default

Quote:
Originally Posted by K4KEV View Post
slightly off topic.....gonna be enjoying a few drinks in the sunshine over the next few weeks.....just finished a 25 litre wash (alcohol) of 20% ABV at around 40p litre
For sure the various pics of the car look good. But seriously - stick in a link to how you produce 20% ABV @ 40p a litre!!! That could save us all enough to buy a lot of man cave toys!!!
Reply With Quote
  #503  
Old 7th June 2013, 09:11 PM
K4KEV's Avatar
K4KEV K4KEV is offline
Senior Member
 
Join Date: Feb 2010
Location: WINGATE CO DURHAM
Posts: 1,511
Default

sorry guys got me numerals wrong it is 80p a litre the 40p is when I cut it 50/50 with water (sacrilage I know) otherwise I'd be bladdered all the time cut it another 50/50 then its the strength of a 5% lager at 20p pint/500ml...its effin dynamite if left alone......I kmnow evtryeeed yt lo0l will do a write next week when I start another ....right must get back to the build.
Reply With Quote
  #504  
Old 11th June 2013, 12:06 PM
K4KEV's Avatar
K4KEV K4KEV is offline
Senior Member
 
Join Date: Feb 2010
Location: WINGATE CO DURHAM
Posts: 1,511
Default

been doing a bit on the trans tunnel.....yet another job which is a PIA, wish I had done it before putting on the side panels.
I have now riveted up the rear panel and the nearside trans tunnel, I have the other side marked out and ready to cut.....again I have been using double sided tape and it is working a treat, much better than messy sikaflex and no worries about whether using too much or too little#.....I will need to seal some areas but I think that is the case for everyone.



Reply With Quote
  #505  
Old 11th June 2013, 12:41 PM
Tatey's Avatar
Tatey Tatey is offline
Senior Member
 
Join Date: May 2009
Location: Leicester
Posts: 827
Default

Kev, don't forget to drill a hole for harness mounts for the transmission side panels, I can imagine it being a PITA to do once riveted on.
__________________
1.8 Silvertop Zetec (ZX6R Carbs + Megajolt) + Type 9

My Build Blog: http://www.haynes.co.uk/forums/showthread.php?t=2736 - Last Update: 31st October 2020

Total Spent so far: Stopped counting
Reply With Quote
  #506  
Old 11th June 2013, 01:43 PM
twinturbo's Avatar
twinturbo twinturbo is offline
Super Moderator
 
Join Date: Jul 2008
Location: Carlisle
Posts: 4,393
Default

Quote:
Originally Posted by Tatey View Post
Kev, don't forget to drill a hole for harness mounts for the transmission side panels, I can imagine it being a PITA to do once riveted on.
F.........k

TT
__________________
You only get a woosh with a dump valve

Build Thread


Man Cave Mantiques



Cecil Street Auto Repairs Garage Carlisle




Build Cost £4181.65 - Last - Wheel Cylinders
Reply With Quote
  #507  
Old 11th June 2013, 02:08 PM
Tatey's Avatar
Tatey Tatey is offline
Senior Member
 
Join Date: May 2009
Location: Leicester
Posts: 827
Default

TT the easiest option for you may be to get a centre punch in for the top of the tunnel and lightly indent it, this should then allow you to see from the outside of the tunnel where you need to drill.
__________________
1.8 Silvertop Zetec (ZX6R Carbs + Megajolt) + Type 9

My Build Blog: http://www.haynes.co.uk/forums/showthread.php?t=2736 - Last Update: 31st October 2020

Total Spent so far: Stopped counting
Reply With Quote
  #508  
Old 11th June 2013, 03:41 PM
K4KEV's Avatar
K4KEV K4KEV is offline
Senior Member
 
Join Date: Feb 2010
Location: WINGATE CO DURHAM
Posts: 1,511
Default

Dont worry guys I did not miss it, the picture just shows the panel offered up I drilled all required holes before I riveted it on ( I deemed it a good idea to have some extra inspection type holes to give easier access to gearbox oil fill hole and some mounting point spanner access
Reply With Quote
  #509  
Old 14th June 2013, 12:03 PM
K4KEV's Avatar
K4KEV K4KEV is offline
Senior Member
 
Join Date: Feb 2010
Location: WINGATE CO DURHAM
Posts: 1,511
Default

Nearly finished the trans tunnel, but waiting for some rivets, so while waiting I decided I wanted to make my short shifter even shorter by around 30mm, I don't want to risk any more than that, but if I do I will make it so ~I can add "some" back on if needed....I think it is one of those thing where you suck it and see
have not threaded it yet just lathed off the thicker part near the thread down to enable a 10mm thread to be cut further down. Does anyone know what the lump off Ally does on a gearstick like this? held on with a circlip.

Reply With Quote
  #510  
Old 14th June 2013, 01:17 PM
ayjay ayjay is offline
Senior Member
 
Join Date: Dec 2010
Location: Coedpoeth near Wrexham, North Wales
Posts: 737
Default

I reckon its a damper
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 05:32 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.