Haynes Forums  

Go Back   Haynes Forums > Haynes Roadster Forums > General discussion
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 8th June 2015, 10:48 PM
SteveH1 SteveH1 is offline
Senior Member
 
Join Date: Jun 2015
Location: Dublin Ireland
Posts: 291
Default

Hi All
My book came today
Just had a quick flick through but doesnt seen to be much about the chassis table

Like how many legs did people put on there bench.
And what height did people build their bench at.
Thanks
Stephen
Reply With Quote
  #12  
Old 9th June 2015, 12:33 AM
vmax1974's Avatar
vmax1974 vmax1974 is offline
Senior Member
 
Join Date: Apr 2011
Location: Teesside
Posts: 1,141
Default

Hi I built my table about 900mm high and 4 legs make the top from the thickest sheet of ply you can get and still brace the underside to eliminate the chance of it sagging time spent bracing and getting it right will save massive headaches later

good luck
Reply With Quote
  #13  
Old 9th June 2015, 08:44 AM
Rosco Rosco is offline
Senior Member
 
Join Date: Sep 2014
Posts: 493
Default

Good luck mate!
__________________
http://www.haynes.co.uk/forums/showthread.php?t=13517

My Build Thread
Reply With Quote
  #14  
Old 9th June 2015, 11:34 AM
CTWV50's Avatar
CTWV50 CTWV50 is offline
Senior Member
 
Join Date: Aug 2010
Posts: 1,297
Default

Pick your wood carefully as getting a straight piece will save you time planing and truing. 1" thick MDF as a table top is my recommendation but don't get it wet. Also use lots of wood glue.
Reply With Quote
  #15  
Old 9th June 2015, 09:35 PM
Badger Badger is offline
Member
 
Join Date: Mar 2008
Posts: 79
Default

I'd be tempted to keep your eyes open for a steel tubular table or something similar and clamp the wood on top - alternatively make the top of the table only and mount it on steel trestles.
The reason for this is that once the chassis is made and tacked strongly together it is very useful to be able to get at it from all angles at a reasonable height.

Here's my build table (and the project before my Roadster):

__________________
If dysfunction is a function, then I must be some kind of genius.
Reply With Quote
  #16  
Old 11th June 2015, 08:30 AM
RichardH RichardH is offline
Senior Member
 
Join Date: May 2015
Location: fife scotland
Posts: 177
Default

i went to a local salvage place dealing in office furniture, i bought three school tables like you would find at primary school, about 4'x2' , they have 25mm box section legs then i bolted 4x2 timber along both sides then sheeted with ply over the top. now i am further on i took out the middle table for working on the engine area and the front and rear is still supported on the other two tables
Reply With Quote
  #17  
Old 20th September 2015, 09:56 PM
SteveH1 SteveH1 is offline
Senior Member
 
Join Date: Jun 2015
Location: Dublin Ireland
Posts: 291
Default

So i got my table built a few weeks ago and decided to put adjustable legs on it as the floor in my shed is rubbish
Untitled by stephen harborne, on Flickr



Untitled by stephen harborne, on Flickr
Reply With Quote
  #18  
Old 20th September 2015, 10:06 PM
SteveH1 SteveH1 is offline
Senior Member
 
Join Date: Jun 2015
Location: Dublin Ireland
Posts: 291
Default

I got my welder during the week its a Swp redline 210
I got it as a package including gas and wire for 750 euro.
i assembled it and it seemed a bit cheap like typical chinese stuff but to my surprise it welded really well

First welds by stephen harborne, on Flickr
The first welds
First welds by stephen harborne, on Flickr

Welder by stephen harborne, on Flickr
The welder
Reply With Quote
  #19  
Old 20th September 2015, 10:15 PM
SteveH1 SteveH1 is offline
Senior Member
 
Join Date: Jun 2015
Location: Dublin Ireland
Posts: 291
Default

So i havnt got my steel yet i will be ordering it tomorrow
But i had some 3 inch angle iron so i started to make a bench for my vice

Vice and bench by stephen harborne, on Flickr

Then i stripped down the vice as its old and looked a bit worse for wear
i then took a wire brush to it


before
Vice and bench by stephen harborne, on Flickr

After
Vice and bench by stephen harborne, on Flickr

Just needs to be painters up now
Reply With Quote
  #20  
Old 20th September 2015, 11:01 PM
K4KEV's Avatar
K4KEV K4KEV is offline
Senior Member
 
Join Date: Feb 2010
Location: WINGATE CO DURHAM
Posts: 1,511
Default

Way to go Steve ....as good as any of our kick off's.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 07:38 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.