![]() |
#11
|
||||
|
||||
![]() Nice one Ronnie, we,re all eager to see your progress photos, keep at it.
![]() ![]() andy |
#12
|
||||
|
||||
![]() To be honest Andy
It was meeting all of you good folks at Stoneleigh that gave me the burning desire to restart my buid. ![]() I was lucky enough to see Spikehaus's build in the flesh a short while ago, that gave me an even bigger kick up the ass ![]() It made me realise that I am not too far behind his progress & in fact, most of the hard work is done. ![]() ![]()
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie ![]() www.roadster-builders.co.uk |
#13
|
||||
|
||||
![]() Well done mate, hopefully not too long before your rolling it around your workshop! And if your energy levels do take a dive, please dont hesitate to give us a call and I will come and give you a hand for the day or summat!
Realy??? one word, megajolt... ![]() ![]()
__________________
http://www.flickr.com/photos/3326151...7611049241239/ |
#14
|
||||
|
||||
![]() Cheers for the offer Jas
![]() Jobs left to do !!?? Cut & weld little squares to cap all of the open ends of the chassis tubes Make & fit CP17 Weld the round bits to the end of the headlamp stalks Finally have a good re-read of the book to make sure that I have not missed anything Ohhh & find out where CP9 & CP25 plates go !!?? May have used them allready but to be honest bu**ered if I know ![]() ![]() Once I have done that little lot, preperation ready for the primer & topcoat ![]()
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie ![]() www.roadster-builders.co.uk |
#15
|
||||
|
||||
![]() i believe CP9 & CP25 go in the rear tub area, bracing bits for uprights of the rear tub, i say i believe as i don,t need them with the Triton tub.
![]() ![]() andy |
#16
|
||||
|
||||
![]() Cheers Andy
Whilst I am on here. I am looking for the general dimensions of Fabbys nosecone Having obtained a Nissan Micra radiator today it is looking a tad too tall ![]() To be exact, I am wanting to know the height of the noscone above the front frame / top rails & how far forward the radiator can come out from the bottom of the front frame without hitting the inside of the lower part of the nonescone !!?? ![]() ![]() If the radiator is suitable, I can then fabricate the radiator mountings. That will be one less area of paintwork to damage ![]()
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie ![]() www.roadster-builders.co.uk |
#17
|
||||
|
||||
![]() just having dinner,
![]() i can get the measurements tomorrow for you. ( nose & my rad are at mothers place). be back soon ![]() andy |
#18
|
|||
|
|||
![]() well done Ronnie keep up the good work fella! Its good to see another car in the flesh its a megajolt in the butt to make progress!(d`ya like what I did there!lol!)
Andrew |
#19
|
||||
|
||||
![]() Quote:
![]() I just wish I could get a Megasquirt on with the build ![]() ![]() ![]()
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie ![]() www.roadster-builders.co.uk |
#20
|
||||
|
||||
![]() Quote:
You are dead right Andy. Just located them in the book. I sort of done my own thing in that area, thats one less job to do then ![]() ![]() Well back out to the workshop, nose to the grindstone & all that Lets see if I can manage to get more than 2 jobs done today ![]() ![]()
__________________
I am not a complete idiot...........Some of the parts are missing !! Ronnie ![]() www.roadster-builders.co.uk |
![]() |
Thread Tools | |
Display Modes | |
|
|