Accelerator cable attach point

[voucht]

Hi everyone,
I don't have my clutch and accelerator cables yet, but I'm working on the pedal box, and I was wondering how the accelerator cable is attached to the accelerator pedal, using this 6,5mm diameter hole? I understood that the Capri clutch cable has an eyed end, (btw, can anybody tell me the diameter of the hole please?), and should be attached to the pedal by a bolt, but what about the accelerator cable?
Pictures are welcome too!
Thank you very much for your answers.
Sylvain

[mgglep]

The Capri clutch cable is ideal it has an 8mm hole in that can simply be bolted to the pedal I used a small piece of tube on the engine bay side to push fit the white plastic thingy into I cut the nipple off the sierra accelerator pedal and welded to the new pedal I can now use the original sierra accelerator cable I simple welded a washer to a piece of tube for the cables bulkhead gromit to push into on the engine bay side I think you can see the pedal box on my Flickr account link below

[Not Anumber]

My accelerator cable goes through a short piece of tube welded into the bulkhead by the pedal and pushes against a washer on the threaded part of the cable to set the tension. This is ok normally when the cable is under any tension but worries me that if the cable gets slack the end of the threaded part can drop out of the end of the tube and then catch on it- this could happen if the pedal is floored and released quickly. Ive limited this to a certain extent by using cable ties to restrict the movement of the outer cable but i will be fabricating a light bracket to hold the threaded section of the outer cable tight up to the bulkhead tube that can be readilly unbolted in case the cable needs to be adjusted or replaced.

[voucht]

Originally Posted by Not Anumber

My accelerator cable goes through a short piece of tube welded into the bulkhead by the pedal and pushes against a washer on the threaded part of the cable to set the tension. This is ok normally when the cable is under any tension but worries me that if the cable gets slack the end of the threaded part can drop out of the end of the tube and then catch on it- this could happen if the pedal is floored and released quickly. Ive limited this to a certain extent by using cable ties to restrict the movement of the outer cable but i will be fabricating a light bracket to hold the threaded section of the outer cable tight up to the bulkhead tube that can be readilly unbolted in case the cable needs to be adjusted or replaced.

Thank you very much, I'll make sure to find a system to secure this part too. But how do you attach the end of the cable to the pedal itself using this 6.5mm diam. hole?

[K4KEV]

I'm going to make a clevis (similar to radio control clevises)

[voucht]

Thank you Kev. I thought about it too, but how will you attach the cable end to the clevis? Actually, what I don't know is how the end of the Sierra accelerator cable looks like (pedal side). I tried to find pictures on Google, but it looks like there are different models. How is yours ?

[flyerncle]

However you end up fittng it make sure it swivels or it will snap the cable as Handy Andy found out with his clutch cable.

[skov]

My throttle cable has a ball on the end, and I was planning to make/buy something like this to attach it to the pedal:

[mgglep]

my sierra accelerator pedal had a nipple on the end of the pedal and the cable has a socket with a black metal clip if you use the nipple and socket it will rotate freely and will be close to the origional so no specialist cables required i will post some pics of mine on my flickr account later

[K4KEV]

on mine it has a ball and socket joint ball on the pedal and socket on end of cable.....if I can go with this system in some way I might use it as is
here is a picture from the drivers footwell looking at the top of the pedal ...the ivory coloured thing is the socket the ball is obvious.