Upright machining? - Haynes Forums

twinturbo Upright machining? 10th January 2010, 08:37 AM

flyerncle Ream it by hand, Axminster do... 10th January 2010, 08:56 AM

Talonmotorsport Yes the bottom ball joint... 10th January 2010, 08:58 AM

flyerncle He's talking about the astra... 10th January 2010, 09:01 AM

twinturbo Anyone got a link to this... 10th January 2010, 09:10 AM

dogwood Cheap as chips, and do the... 10th January 2010, 09:15 AM

twinturbo And the taper is correct on... 10th January 2010, 09:28 AM

Talonmotorsport Silly me. You'll need the... 10th January 2010, 09:33 AM

dogwood Silly you? silly... 10th January 2010, 09:37 AM

twinturbo and the taper angle is... 10th January 2010, 09:42 AM

dogwood Yup.:D Seemed to be perfek.... 10th January 2010, 09:50 AM

twinturbo so when reamed, the OD of the... 10th January 2010, 09:55 AM

dogwood See, now you getting... 10th January 2010, 10:03 AM

HandyAndy i did mine as Dogwood... 10th January 2010, 11:09 AM

twinturbo Sounds easy enough, I just... 10th January 2010, 11:16 AM

twinturbo Which was the question i was... 10th January 2010, 03:12 PM

twinturbo Anyone got one to measure... 10th January 2010, 06:34 PM

RAYLEE29 I used the 19mm Axminster one... 10th January 2010, 07:34 PM

twinturbo That still does not answer... 10th January 2010, 07:53 PM

Davey A couple of points are coming... 10th January 2010, 08:09 PM

RAYLEE29 whilst i agree with what you... 10th January 2010, 08:29 PM

Davey A reamer can't cut oversize... 10th January 2010, 09:49 PM

RAYLEE29 Davey this is a forum and... 10th January 2010, 11:28 PM

Davey Ray I'll agree to disagree... 11th January 2010, 06:52 AM

Talonmotorsport Thank god thats all... 11th January 2010, 08:20 AM

twinturbo / It cuts a hole the wrong... 11th January 2010, 08:52 AM

Peter-C To save me trolling through... 26th February 2010, 08:57 PM

AshG I was in axminster tools... 26th February 2010, 10:23 PM

RAYLEE29 Sorry you didnt understand my... 10th January 2010, 08:23 PM

twinturbo I guess if they are not... 10th January 2010, 08:29 PM

RAYLEE29 mine worked fine:) 10th January 2010, 08:32 PM

HandyAndy mine too :) andy 10th January 2010, 08:32 PM

flyerncle Me three no probs :) 10th January 2010, 08:34 PM

twinturbo Cheers. so it would be a... 10th January 2010, 09:22 PM

AshG thats funny andy if you look... 26th February 2010, 10:32 PM

AshG i cant seem to find one where... 26th February 2010, 10:55 PM

Big Vern Hi Ash, Did you put the ream... 26th February 2010, 10:59 PM

AshG yes i have clamp attachments... 26th February 2010, 11:18 PM

Peter-C Cheers Ash for the photos,... 27th February 2010, 12:35 PM

Big Vern 1992 - 1995 Cavalier has... 26th February 2010, 10:36 PM

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode