|
|
|
|
#1
9th May 2011, 09:19 PM
|
|||
|
|||
No worries mate, I didn't expect you to drive all the way down here! :-)
We will however have a van somewhere near, Milton Keynes about 40 mins away, on Friday at some time but I'm not sure exactly when. Would you be so kind as to give me until lunchtime tomorrow (tuesday) to check the timing and if it's ok for the van to make the slight detour (read convince the boss!)? I just don't want to say definite yes now and mess you around later. Would you be able to let me know a rough time your planning on leaving the area? Also, whilst not that important, which gearbox is the chassis set up for? Thanks in advance, Ashley 
|
|
#2
9th May 2011, 09:30 PM
|
||||
|
||||
|
No probs Ashley
It's for a type 9 box. I have to pick a car up at 2 pm. I can probably be in the area from around 1pm. Will be leaving area around 3 pm. Could detour via MK if that helps. Gimme a ring sometime, I'll pm you my number
__________________
Costs so far :- Too much but somehow not quite enough  http://alansroadster.blogspot.com/
|
|
#3
10th May 2011, 08:12 AM
|
|||
|
|||
|
Hi mate, just got to work and thought it'd be an idea to make sure it would fit in the van. Can you let me know the dimensions of the chassis please mate, or anyone else out there know?
I got your pm too, I'll give you a shout when I know it'll fit and that the van can get there. If you're happy to go to mk, that would make things easier for me to organise with the driver, but if not, there's no trouble in him coming to you. Cheers Ash
|
|
#5
10th May 2011, 12:00 PM
|
||||
|
||||
|
Quote:
__________________
Website http://www.talonmotorfabrication.co.uk/ Direct email phil@talonmotorfabrication.co.uk talonmotorfabrication@gmail.com Mobile office hours 07514098334
|
|
#6
10th May 2011, 12:33 PM
|
|||
|
|||
|
Captaincrash, unfortunately I have bad news. It has become apparent that the van is no longer headed up to Milton Keynes on Friday due to some problems with the bits that were going to be delivered. I'm going to have to let this one slip by I'm afraid. Im genuinely sorry to have got your hopes up, but thank you for allowing me to have the time to check.
I really hope you are able to sell the chassis, Best regards Ashley
|
|
#7
10th May 2011, 02:49 PM
|
||||
|
||||
|
No problem. Anyone else for a genuine bargain? Quick, to save me grief of ebay selling.
__________________
Costs so far :- Too much but somehow not quite enough http://alansroadster.blogspot.com/
|
|
#8
10th May 2011, 03:29 PM
|
|||
|
|||
|
Hello Captain....and everyone else, this is a bit scary...1st post `n all that. Meant to do the intro thing but in at the deep end is the best way sometimes!
I would be interested in your chassis. Had a look at your blog thing and you mentioned Handyandy had looked over it. What did he find, is there a lot to do? would it be within the scope of a welding muppet such as myself? Could poss meet you on your travels on friday Best regards Andy...yep `nuvver `un
|
|
#9
10th May 2011, 05:15 PM
|
||||
|
||||
|
Hi Andy, welcome to the forum. Handy mentioned one of the front wishbone mounts was askew, and a couple of the welds at the back end needed tidying up. Make me an offer, need the space and its far too good to chop up.
__________________
Costs so far :- Too much but somehow not quite enough http://alansroadster.blogspot.com/
|
|
#10
10th May 2011, 07:00 PM
|
|||
|
|||
|
Quote:
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
