Hello chaps...

[PorkChop]

Multiquote time!

Originally Posted by Deanno

may i be the fist to say welcome to the forum.
where abouts are you?

Cheers for the welcome My location? Put it this way, you're not the only Welshman to post on this thread

Originally Posted by Talonmotorsport

You may have to play with the speedo if you use a mazda gear box with a sierra diff depending on wether you use mazda/ford or after market clocks. Theres not much difference between the type9 and mt75 footwells only 50mm you may be better off with a hanging pedal box rather than a book spec.

One of the few things that are set in stone is the dashboard. I'd like a minimalist aftermarket dash panel, so hopefully the speedo won't be a problem regardless of the final spec.

Originally Posted by SeriesLandy

Ive got size 12 feet and with my trainers on I can operate the pedals, Standard type 9 gearbox/tunnel. I'll be buying some slimmer shoes for driving once the car is on the road.

I tried out a Dutton pedal box in trainers once. It didn't go well

Originally Posted by twinturbo

I would go MT75 tunnel anyway, gives more scope when you want to upgrade.

If your planning on MX5 rear then I see no real sense in going for a sierra engine and box as you can get better power from the MX5 and it may cost less.

TT

TBH a Pinto/CVH lump isn't on the cards. I'm still undecided on the rear set-up but it'll either be Sierra or MX5 - it depends on how much extra space the offset MX5 diff takes up (based on Skov's build thread). If I do go for a MX5 diff, then in all likelihood the whole build will be MX5 based. I think I might need to have a word with HandyAndy and Spud but I'll wait for the build notes to get on the Saturn website next week first

Originally Posted by mark

Mock up the space for the two options and try it out, i have type 9 tunnel so the wider of the two options and i find the pedals a little close and im only a size 11 but they are quite broad which is what makes the most impact really

Im used to it now but prefer to wear slimline shoes

That's what I was thinking about doing. I've had cars with small footwells before and have been OK. We'll see...

Thanks for the welcome and the help so far guys!

[baz-r]

welcome
get on to voodo autokits if i was you thay have the plans for a full mx5 doner roadster and also do ford based roadster bits to all same as 3ge stuff so its all top quality
thay should be able to sort you out what ever you go for mazda,ford or hybrid

[PorkChop]

Originally Posted by baz-r

welcome
get on to voodo autokits if i was you thay have the plans for a full mx5 doner roadster and also do ford based roadster bits to all same as 3ge stuff so its all top quality
thay should be able to sort you out what ever you go for mazda,ford or hybrid

Do you have a link Baz? I looked on the Vodou site but could only find chassis sketches rather than build plans...cheers for the welcome too

[PorkChop]

Is HandyAndy still doing flat pack chassis kits? I've noticed that he hasn't posted for a couple of months (and I understand he has his reasons); I just don't want to bother him unnecessarily

[skov]

Originally Posted by PorkChop

I'm still undecided on the rear set-up but it'll either be Sierra or MX5 - it depends on how much extra space the offset MX5 diff takes up (based on Skov's build thread).

Welcome PorkChop,

You don't lose that much to be honest. Saturn have flared the tunnel out by 62mm, so you're only losing 31mm either side.
It's particularly noticable on mine as my seats are a bit on the wide side and only just fit between the rails, if they were an inch narrower it wouldn't be a problem.

[PorkChop]

Originally Posted by skov

Welcome PorkChop,

You don't lose that much to be honest. Saturn have flared the tunnel out by 62mm, so you're only losing 31mm either side.
It's particularly noticable on mine as my seats are a bit on the wide side and only just fit between the rails, if they were an inch narrower it wouldn't be a problem.

Cheers for the welcome.

That sounds good; really good It's making it increasingly likely that old 5 bits might find a new home...I'll wait until the plans are up on the SSC site and look at the dimensions before committing to a particular spec