|
|
|
|
#1
10th February 2013, 08:07 AM
|
||||
|
||||
Saturday update...
   Yes - it's straight (I plan to hide reverse motor and handbrake lever in it) 
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe 
|
|
#2
10th February 2013, 08:10 AM
|
||||
|
||||
    And now... should I fully weld it, or make rear suspension framework... Chassis is bolted/welded to build table, so in my opinion it would be better to fully weld it now, then make rear framework, and in the end - weld suspension brackets...
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe Last edited by loony : 10th February 2013 at 08:20 AM.
|
|
#3
10th February 2013, 08:14 AM
|
||||
|
||||
|
I also made bucket's insert - for electrolysis cleaning (front calipers, maybe upright/hubs):
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe
|
|
#4
16th February 2013, 08:02 PM
|
||||
|
||||
|
Another Saturday...
First, I got my Birthday present - mainly form myself, but my "other half" had her contribution in it. Now I'm ready to take care after all this nuts ;-)  I also picked up Fiat Cinquecento seats - bought some time age for... about £10. Naturally seats are too wide, but... I need only runners, which are very easy to modify (only one bar/tube). Universal runners alone cost more than this whole seats...  So, first task was to separate runners form seats...  Few minutes later... 
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe
|
|
#5
16th February 2013, 08:09 PM
|
||||
|
||||
|
On Thursday I picked upa GRP seats for "client". As my seats will be same but 50mm wider (these are 39cm wide so they are tight), I can plan where I need my runners.
   I also made steering support frame... 
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe
|
|
#6
16th February 2013, 08:15 PM
|
||||
|
||||
|
Finally I couldn't resist to trial fit some components:
  Because I didn't want to start something bigger - I prepared tubes and welded pedals...  Next I will fully weld chassis, before I move it forward to weld rear suspension frame...
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe
|
|
#7
18th February 2013, 09:41 PM
|
||||
|
||||
|
Today I got my MKIndy inspired laser cut rear uprights:
  And... my first SolidWorks finished project - seat mounting plate: 
__________________
Lucas ZX9R BEC Haynes Roadster - build cost so far: £1125 My build thread "Whatever you can do or dream you can, begin it. Boldness has genius, power, and magic in it." J.W.Goethe Last edited by loony : 19th February 2013 at 07:31 AM.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
